The BLUEFIRE triple flame torch head is a hand-held torch head with a three-point flame, meant for brazing, soldering and general heating jobs on larger pipe and fittings. Per the listing it is stainless steel, weighs about 7 ounces and is rated at up to 25,590 BTU on MAPP-type gas, with propane also listed. It suits you if you want a wider, more even flame than a single-jet head. Skip it if you need a pinpoint flame for tiny work, or if you cannot confirm the thread matches your fuel cylinder.
BLUEFIRE Triple Flame Torch Head at a Glance
| Item | Per the listing |
|---|---|
| Type | Triple flame torch head |
| Material | Stainless steel |
| Maximum output | 25,590 BTU |
| Maximum flame temperature | 2,372°F (1,300°C) |
| Weight | About 7 ounces |
| Fuels named | MAPP-type gas and propane |
| Typical jobs | Brazing, soldering and heating larger pipe |
These figures come from the retailer listing, not from bench measurements. Output and flame temperature depend on the fuel and the cylinder, so treat them as maximums.
Who Should Buy It
- Home and shop users who braze or solder copper pipe and fittings and want a wider flame.
- Hobbyists who heat small parts for bending, loosening or tempering work.
- Anyone who already owns a compatible fuel cylinder and wants a lighter head to replace a worn one.
Skip it if you work on thin sheet or tiny joints where a three-point flame will overheat the surrounding metal, or if you need a documented heavy-duty industrial rating.
Fuel Options and Compatibility
The listing names MAPP-type gas and propane. MAPP-type fuel burns hotter, which is why the maximum figures only apply to it. Propane is cheaper and easier to find, but gives lower heat.
- Thread: Check the listing for the connection type and match it to your cylinder. Do not force a head onto a cylinder that does not thread on smoothly.
- Fuel on the label: Use only a fuel the cylinder label and the head maker both allow.
- Not an oxy-fuel torch: This is an air-fuel head. It does not connect to oxygen hoses or regulators.
How to Use It Safely
- Work outdoors or in a well-ventilated area and clear flammable material from the bench.
- Wear safety glasses and heat-resistant gloves.
- Close the torch valve, then thread the head onto the cylinder by hand until snug.
- Check the connection for leaks with soapy water before lighting. Never test with a flame.
- Open the valve slightly, light with a striker and adjust to a stable flame.
- When finished, close the cylinder valve, let the head cool, and store the cylinder upright in a cool, dry place.
Limitations to Know
- A three-point flame covers more area, which is less precise than a pencil flame.
- The head alone does not include fuel. You need a compatible cylinder.
- Maximum figures are listed values. Real heat depends on fuel, cylinder pressure and how far you open the valve.
- The listing does not give certifications or warranty terms that this page can confirm, so check the Amazon page before buying.
Related reading: BLUEFIRE hot turbo torch head review | Propane MAPP gas torch head review | BLUEFIRE MAPP gas cylinder review
Frequently Asked Questions
What is the BLUEFIRE triple flame torch head used for?
It is used for heating jobs such as brazing and soldering pipe and fittings, where a wider three-point flame helps spread heat.
Which fuels does it use?
The listing names MAPP-type gas and propane. MAPP-type gas gives the higher maximum heat. Confirm the thread and fuel on the listing and on your cylinder label.
Does it come with a fuel cylinder?
No. It is a torch head only, so you need a compatible cylinder bought separately.
Can I use it indoors?
Only with good ventilation, a clear work area and a fire extinguisher nearby. An open flame and fuel gas should not be used in a closed space.
Bottom Line
The BLUEFIRE triple flame torch head is a light stainless head for brazing, soldering and general heating, with a wide three-point flame. Buy it if you have a matching cylinder and want broader heat. Skip it if you need fine-point control or documented industrial ratings.
