The Ejoyous MIG welding tips are a 20-pack of copper contact tips that, per the Amazon listing, fit Binzel 15AK-style MIG torches in 0.8 mm (0.030 in) and 1.0 mm (0.040 in) sizes. They are a low-cost spare for small MIG and mini MIG torches. Buy them only if your torch uses the same 15AK-type tip and you match the tip bore to your wire. The Ejoyous MIG welding tips 20-pack fit 15AK style guns.
Ejoyous MIG Welding Tips: Quick Specs
| Item | Detail (per the listing) |
|---|---|
| Product | Ejoyous MIG welding tips, pack of 20 (ASIN B086XKMG3P) |
| Torch fit | Binzel 15AK-style MIG torches |
| Wire sizes | 0.8 mm (0.030 in) and 1.0 mm (0.040 in); check which size your pack contains |
| Material | Copper (listed as red copper) |
| Length | About 2.3 cm (0.9 in) |
Not hands-on tested for this post. Confirm the thread, length and size on the live listing against your torch before ordering.
Choose the Right Tip Size
A contact tip passes current to the wire, so its bore has to match the wire diameter. A tip that is too large lets the wire wander and arc poorly. A tip that is too small makes the wire stick or feed badly.
| Wire diameter | Tip bore to use |
|---|---|
| 0.030 in (0.8 mm) | 0.030 in / 0.8 mm tip |
| 0.035 in (0.9 mm) | 0.035 in / 0.9 mm tip |
| 0.040 in (1.0 mm) | 0.040 in / 1.0 mm tip |
Check your torch and wire spool label first. If your torch is not a 15AK type, compare thread and length against your original tip.
How to Swap a MIG Contact Tip
- Switch the welder off and let the torch cool.
- Remove the nozzle and cut off the wire at the tip.
- Unscrew the old tip and, if fitted, check the diffuser or gas diffuser for spatter.
- Thread the new tip in until snug. Do not over-tighten it.
- Refit the nozzle, feed the wire through and trim it to the right stick-out.
When to Replace a Tip
- The bore is worn oval or the wire arcs inside the tip.
- The wire burns back and fuses to the tip.
- Feeding is rough even though the liner and drive rolls are clean.
- Spatter has built up on the tip end and cleaning does not help.
If you have feeding trouble that a new tip does not fix, see MIG welder wire feeds but no arc.
Pros and Limitations
Pros
- A 20-pack keeps spares on hand for a small torch
- Copper tips conduct current and heat well
- Two common wire sizes are listed
Limitations
- Only suits 15AK-style torches, not every MIG gun
- Pack contents by size must be confirmed on the listing
- Tips wear out; heavy use means frequent replacement
Related Tip Reviews
Compare other contact tip packs before you buy: TimelyDu 20-pack, the 30-pack of MIG tips and FORTON tips.
Frequently Asked Questions
What torch do Ejoyous MIG welding tips fit?
The listing says they fit Binzel 15AK-style MIG torches. Compare the thread and length with your current tip before ordering.
What wire sizes do they support?
The listing mentions 0.8 mm (0.030 in) and 1.0 mm (0.040 in). Match the tip bore to your wire diameter.
How do I install a MIG contact tip?
Turn the welder off, let the torch cool, remove the nozzle, unscrew the old tip, thread the new one in snug and refit the nozzle.
Can I reuse a contact tip after cleaning?
Light spatter can often be cleaned off. If the bore is worn oval or the wire has fused inside, replace the tip.
What is the warranty on these tips?
Not verified for this post. Check the Amazon listing and seller for return and warranty terms.