As an Amazon Associate, Garage Welding may earn from qualifying purchases. This does not change the price you pay.
The Watris Veiyi soldering plier is an 8-inch hand tool designed to hold two wires together so you can solder a splice with one hand free. This Watris Veiyi soldering plier review is based on the Amazon listing, not hands-on testing. It is worth a look if you do wire splices and car or hobby wiring; skip it if you need a heat-resistant clamp for torch work.
Quick specs at a glance
| Item | Per the listing |
|---|---|
| Type | Wire-holding soldering plier |
| Length | About 8 inches |
| Weight | About 0.21 kg |
| Operation | One-handed; holds two wires |
| Build | Metal jaws with a handle grip |
Jaw opening and wire-gauge limits are not given in a form we can verify, so check the listing and photos for them.
Check current price on Amazon →
What it is and who it suits
When you splice two wires, one of the biggest annoyances is keeping them aligned while you heat and feed solder. This plier clamps the two wires side by side so you can hold the iron in one hand and solder in the other. The listing and buyers often point to automotive wiring repairs, speaker wire, and hobby electronics.
It is a hand tool, not a heat sink. Solder joints get hot, so keep the plier body and your fingers away from the heated wire, and do not use it as a torch clamp.
How to check it fits your needs
- Wire gauge: confirm the plier can close on the thickness you use. Small hobby wire and thick automotive cable behave very differently.
- Handle material: the grip should be non-conductive or at least comfortable. Do not use it on live circuits unless the handle is clearly rated for that.
- Jaw design: look for jaws that hold two wires parallel with a small gap to the work, so the solder bridges them.
- Length and weight: eight inches and about 0.21 kg is manageable for repetitive splicing, but it may feel big for tiny electronics.
- Wire type: for automotive harnesses, make sure you also have heat-shrink tube ready to slide over the splice.
Pros and limitations
| Pros | Limitations |
|---|---|
| Frees a hand during splicing | Not a replacement for a proper crimp where one is specified |
| Metal jaws and simple mechanism | Limited to the wire sizes the jaws accept |
| Comfortable grip for repetitive work | Can conduct heat to the handle if overheated |
| Light enough for bench and in-car work | Positioning very thin wires can take practice |
Check current price on Amazon →
How to solder wire splices with a holding plier
- Strip about 10–15 mm of insulation, twist the strands, and slide heat-shrink onto one wire first.
- Place the two stripped ends side by side in the jaws, with the bare copper just past the jaw edge.
- Heat the wires with the iron tip, not the solder, then touch the solder to the wire so it flows into the strands.
- Let the joint cool before you release the plier. Moving it early can crack the joint.
- Slide the heat-shrink over the cooled splice and shrink it with a heat gun.
For the soldering itself, a mat and fume extraction help: see our soldering mat review and solder fume extractor review.
Alternatives and related guides
- Solder wire holder stand to keep the solder spool tidy while you work.
- TI-SMART soldering iron kit for the iron to pair with it.
- Hicello soldering iron kit as another beginner kit option.
Frequently Asked Questions
What is a soldering plier used for?
A soldering plier like this holds two wires together so you can heat and solder them without a third hand. It is commonly used for splicing speaker, automotive or hobby wires. It is not designed to clamp parts for torch brazing or welding.
Can I use it on live wires?
No. Always disconnect power and the vehicle battery before soldering. Unless the handle is clearly rated for electrical work, assume it is not insulated, and never use soldering pliers on energized circuits.
What wire sizes does this plier hold?
The listing describes it as holding two wires but jaw capacity is not clearly stated. Check the product photos and description for the wire gauge it accepts before you order, especially if you work with thick automotive cable.
Do I still need heat-shrink with a soldered splice?
Yes. Solder alone leaves bare metal exposed and the joint can be stiff. Slide heat-shrink over the wire before soldering, then shrink it over the cooled joint to insulate and give the splice some strain relief.
Conclusion
The Watris Veiyi plier is a simple way to hold two wires steady while you solder a splice. Confirm the wire size it grips and treat it as a holding aid, not a heat-proof or insulated tool.
Check current price on Amazon →
