🔧 Practical welding guides, tested in a real garage
Welding Wire & Rod Reviews

AZZUNO Mig Solid Welding Wire Review

AZZUNO MIG solid welding wire - product photo

The AZZUNO MIG solid welding wire is a .035 in ER70S-6 solid steel wire sold on 2 lb spools. It is a fit for mild steel work on a gas MIG machine with 75/25 argon and CO2 gas, and it is not a gasless wire. This review is built from the Amazon listing and does not claim hands-on testing.

Quick Verdict

Verdict: A small-spool ER70S-6 option for hobby and repair work on mild steel, if your welder takes 2 lb spools.

Best for: Garage welders running gas MIG on mild steel who want to buy wire in small quantities.

Skip it if: your machine is flux-core only, takes 10 lb or larger spools, or you need wire for stainless or aluminum.

Check Price on Amazon →

AZZUNO MIG solid welding wire: key specs

Details below are from the listing. Confirm pack size and spool count on the current page before you order.

Specification Detail
Wire type ER70S-6 solid MIG wire
Diameter .035 in
Spool size 2 lb spools, listed as a 2-pack
Base metal Mild steel
Shielding gas External gas required (75/25 argon and CO2 is the usual choice for ER70S-6)
Packaging Upgraded spool with moisture absorbers, per the listing
ASIN B0CSYGHLHX

What ER70S-6 solid wire is good for

ER70S-6 is a common copper-coated solid wire for mild steel. It carries extra deoxidizers, so it tolerates a little mill scale or light rust better than many other solid wires. You still get the cleanest welds on bare, clean metal.

Solid wire needs shielding gas, so it is best used in a sheltered garage or shop. Even a light breeze can blow the gas away and cause porosity. If you weld outdoors or have no gas cylinder, a gasless flux-core wire is the better pick; see our AZZUNO flux core wire review.

Check that it fits your welder

  1. Wire size: Your drive roll groove, liner and contact tip must all match .035 in.
  2. Spool size: Many small machines take 2 lb spools, but check the spool diameter and hub fit in your manual.
  3. Gas: You need a cylinder, regulator and gas hose set up for MIG. Solid wire will not work properly in gasless mode.
  4. Polarity: Solid wire normally runs with the electrode positive. Set it according to your manual.
  5. Metal: Use this wire on mild steel only. Stainless and aluminum need their own wire.

Pros

  • ER70S-6 is a versatile mild steel wire with good tolerance for light surface contamination.
  • Small 2 lb spools suit occasional use and small machines.
  • Moisture absorbers in the spool help keep the wire dry, per the listing.
  • Cleaner, less spatter-prone welds than flux-core when the gas setup is right.

Limitations

  • Needs a shielding gas cylinder and regulator.
  • Small spools run out quickly on bigger projects.
  • Not suitable for stainless or aluminum.
  • Price per pound is usually higher on small spools, so compare with larger spools if you weld often.

Check Price on Amazon →

Tips for cleaner welds

  • Clean oil, paint and heavy rust from the joint.
  • Use a push or slight drag angle and keep the stickout short and steady.
  • Start from the voltage and wire speed chart on your welder, then fine-tune on scrap.
  • Keep the spool in a dry place or sealed bag when not in use.
  • Wear a welding helmet, gloves and flame-resistant clothing, and keep the area ventilated.

Alternatives and related guides

Compare other solid wire options in our solid MIG welding wire ER70S-6 review and the TOOLIOM ER70S-6 welding wire review. For the machine side, see the AZZUNO 8-in-1 MIG welder review.

Frequently Asked Questions

What can I weld with AZZUNO MIG solid welding wire?

It is intended for mild steel. ER70S-6 is not meant for stainless steel or aluminum, which need different filler wires.

Does this wire need shielding gas?

Yes. It is solid wire, so it needs an external shielding gas. Argon and CO2 mixes such as 75/25 are the common choice for ER70S-6.

Can I use it outdoors?

Only with care. Wind can blow shielding gas away from the weld, which causes porosity. Weld in a sheltered area or use gasless flux-core wire for outdoor work.

How should I store the wire?

Keep it in a cool, dry place, ideally sealed in a bag with desiccant. Moisture and rust on the wire cause feeding problems and porosity.

Will it fit any MIG welder?

No. Check that your machine supports .035 in wire, 2 lb spools and gas operation, and that the drive roll, liner and contact tip match the wire size.

Final verdict

This AZZUNO ER70S-6 wire makes sense if you run a gas MIG welder on mild steel and want small spools. Skip it if you need gasless wire or a larger spool. Check the current listing for the spool count and any updated details before you buy.

Check Price on Amazon →

Alfred Chase
Alfred Chase

Alfred Chase is the main voice behind Garage Welding, with 15 years of experience in welding. Since 2025 he has written the site's welding guides and product reviews, covering MIG, flux-core, TIG and stick welding, filler metals, welding machines, torch parts, helmets, gloves and shop safety gear. He writes for people welding in a home garage or small shop, so he sticks to what helps: clear settings, safe habits, honest limits and fixes for the problems beginners run into. His product reviews are based on manufacturer specs and listing details, and he says plainly when something isn't confirmed.

Leave a Comment

Your email address will not be published. Required fields are marked *