The Forney 30505 E6013 is a 5/32-inch E6013 stick electrode sold in a 5-pound box. E6013 is the easy-running, all-position rod for mild steel, and the 5/32 size is the heaviest common choice in the class. It suits thicker light-to-medium steel and fabrication work on a welder with enough output. Skip it if your machine tops out at light 120V output, if you weld rusty steel, or if the job needs a low-hydrogen rod.
This page is based on retailer listings and class standards, not hands-on testing. Confirm the size and pack on the Amazon listing before ordering.
Quick Verdict
Best for: welders with a stick machine strong enough for 5/32 in rods who want a smooth-running 5/32 in mild steel rod in bulk.
Skip if: you have a small 120V welder, weld dirty steel, or need a low-hydrogen electrode.
Bottom line: the big-diameter E6013 in the Forney range. Check that your welder can run it before choosing it over the 3/32 in sizes.
Forney 30505 E6013 specs at a glance
| Specification | Detail |
|---|---|
| Brand | Forney |
| Item number | 30505 |
| Classification | E6013 mild steel stick electrode |
| Diameter | 5/32 inch, per NAPA |
| Pack size | 5 lb, per NAPA |
| Current | NAPA lists AC, DCEP and DCEN |
| Positions | All-position (the 1 in E6013) |
| Tensile strength | 60,000 psi minimum (the 60 in E6013, a class minimum) |
| Penetration | Shallow to medium (typical of E6013) |
| Not for | TIG, rusty steel, low-hydrogen procedure work |
Amperage depends on your machine and the joint. Use the range printed on the box for 5/32-inch rods. Rods this size generally need more output than many small 120V hobby welders can supply.
What Is the Forney 30505 E6013 Welding Rod?
E6013 rods have a titania-type coating made for easy arc starts, light spatter and slag that releases cleanly. The 5/32-inch core carries more current and puts down more metal per pass than the 3/32 in and 1/8 in sizes.
That makes it suited to thicker mild steel and flat or horizontal fillet and lap welds. On thin sheet it is the wrong size, because the arc will burn through.
Who Should Buy It and Who Should Skip It
- Buy it for medium-thickness mild steel fabrication on a welder rated for 5/32 in rods.
- Buy it if you use rods regularly and want a 5 lb box.
- Skip it for thin sheet metal. A 3/32 in rod such as the Forney 30305 is easier to control.
- Skip it for rusty or painted steel, where an E6011 digs better.
Fit and Setup Checklist
- Machine: confirm your stick welder can run 5/32-inch rods at the amperage on the box.
- Duty cycle: large rods use more current, so expect rest breaks on a small machine.
- Current: E6013 runs on AC or DC. Follow the package for your machine.
- Metal thickness: choose this size for thicker mild steel. Thin steel needs a smaller rod.
- Metal type: mild steel only.
How to Run E6013 Rods
- Clean the joint to bright metal and clamp the ground close to the weld.
- Set amperage in the range on the box and test on scrap of the same thickness.
- Hold a short arc and move at a steady pace. Slow down if the bead is narrow and tall.
- Let the weld cool, chip the slag with safety glasses on, and brush before the next pass.
Safety and Storage
Wear a welding helmet, leather gloves and flame-resistant clothing, and weld with ventilation. Do not weld galvanized or painted steel without removing the coating, because zinc and paint fumes are hazardous.
Keep the rods in a dry, closed container. E6013 is not a low-hydrogen rod, but damp flux still causes spatter and poor starts.
Pros and Limitations
Pros
- Easy arc starts and smooth bead typical of E6013
- Heavy 5/32 in size puts down more metal per pass
- All-position classification
- NAPA lists AC, DCEP and DCEN polarity
Limitations
- Needs a welder with enough output for 5/32 in rods
- Too large for thin sheet steel
- Shallow-to-medium penetration, not for dirty steel
- Not a low-hydrogen rod
Related guides: Forney 30305 E6013 (3/32 in, 5 lb) · Forney 30301 E6013 (3/32 in, 1 lb) · Forney 31210 E6011 for dirty steel
Frequently Asked Questions
What size is the Forney 30505 E6013 rod?
NAPA lists Forney 30505 as a 5/32 in x 5 lb E6013 electrode. Confirm the size on the Amazon listing before ordering.
What welder do I need for 5/32 in E6013 rods?
One that can supply the amperage printed on the box for 5/32 in rods. Many small 120V hobby welders cannot, so check your manual first.
Can I use it on AC and DC?
E6013 is made for both, and NAPA lists AC, DCEP and DCEN for this item. Follow the package for your machine.
Is a 5/32 in E6013 rod good for beginners?
E6013 is easy to run, but a 5/32 in rod needs a powerful machine and a steady hand. Beginners usually start with 3/32 in or 1/8 in rods.
Can it weld rusty steel?
It is not the best choice. Clean the joint first or use a digging rod such as E6011.
Bottom Line
The Forney 30505 E6013 is the large-diameter option in the E6013 range. It makes sense for medium-thickness mild steel and a welder with the output to run it, and the 3/32 in sizes are a better start for thin steel or small machines.