🔧 Practical welding guides, tested in a real garage
Welding Tools & Accessories Reviews

Chicago Pneumatic CP714 Air Hammer Review: Specs and Fit

Chicago Pneumatic CP714 air hammer - product photo

The Chicago Pneumatic CP714 is a pistol-grip air hammer with a 0.401 inch shank, rated by retailers at about 2,000 blows per minute. It is a body-shop style hammer for chiseling, panel and exhaust work and light riveting. It uses far less air than a faster utility hammer such as the Chicago Pneumatic CP7111, which makes it easier to run from a modest compressor, but it hits slower. The Chicago Pneumatic CP714 air hammer is a compact tool for chiseling and panel work.

Chicago Pneumatic CP714 at a Glance

Item Retailer-listed spec
Type Pistol-grip pneumatic hammer with a positive-action trigger
Shank 0.401 in (round)
Blows per minute 2,000
Stroke About 3-1/8 in
Average air consumption About 2 CFM
Air inlet 1/4 in (NPTF per one retailer)
Weight About 3.3 to 3.6 lb, depending on the retailer
Kit versions Some retailers sell a CP714 kit with chisels and a case; check what your listing includes

These figures come from retailer listings, not from hands-on testing. Confirm them in the manual for the exact version you buy.

Check price on Amazon

What It Is and Who It Suits

An air hammer drives a chisel or punch back and forth very quickly. The CP714 is sold for body work: front-end and exhaust jobs, frame work, cutting and shaping sheet metal, and general chiseling.

It suits hobbyists and restorers who already own a compressor and want a controllable hammer for panel and rusted-part work. For welders it can chip heavy slag or spatter, although a hand tool such as the CHOWEL BHS-W330 chipping hammer or a chipping hammer and wire brush set is usually enough for normal weld cleanup.

How to Check It Fits Your Setup

  • Compressor: compare the roughly 2 CFM average figure with the CFM your compressor delivers at working pressure, not the tank size. Real use can draw more air than the average.
  • Hose and fittings: the inlet is a 1/4 inch thread, so you need a matching quick coupler and a hose of suitable diameter.
  • Accessories: chisels, punches and cutters must use a 0.401 inch round shank with a retainer.
  • Lubrication: pneumatic tools need air tool oil or an inline oiler. Follow the manual.
  • What is included: bare tool and kit listings use different model numbers, so check whether bits and a case are in the box.

Check price on Amazon

Pros and Limitations

Pros

  • Low listed air use, so it is easier to feed from a smaller compressor
  • Standard 0.401 inch shank with a wide choice of bits
  • Positive-action trigger for speed control
  • Light enough for overhead and under-car work

Limitations

  • 2,000 blows per minute is slower than faster utility hammers
  • Loud and vibrating; hearing and hand protection are needed
  • Bits are often sold separately
  • Specs vary slightly between retailer listings

Using an Air Hammer Safely

  • Wear safety glasses or a face shield, hearing protection and gloves.
  • Use only chisels with a retainer or spring made for the tool; a loose bit can fly out.
  • Disconnect the air line before changing the bit and never point the tool at anyone.
  • Do not exceed the air pressure stated in the manual.
  • Let welds cool and keep flammables clear of sparks from chisel work.
  • Drain moisture from the compressor tank regularly.

Frequently Asked Questions

What compressor do I need for the Chicago Pneumatic CP714?

Retailers list an average air consumption of about 2 CFM. Choose a compressor that delivers more than that at the working pressure in the manual, because bursts of heavy use draw more air than the average.

What shank size does the CP714 use?

It takes 0.401 inch round-shank accessories. Check that any chisel or punch lists the 0.401 inch shank and has a retainer that suits the tool.

How does the CP714 differ from the CP7111?

Both are pistol-grip hammers with a 0.401 inch shank. Listings show the CP714 at about 2,000 blows per minute and 2 CFM, while the CP7111 is listed at 3,000 blows per minute and 6.25 CFM average, so it hits faster but needs more air.

Can I use it for welding slag?

A chisel on an air hammer can chip heavy slag and scale, but let the weld cool first and wear eye protection. For routine slag removal a manual chipping hammer is simpler.

Final Thoughts

The CP714 is a controllable, low-air-use body-shop hammer. It is a reasonable pick if your compressor is modest and the work is panels, exhaust and light chiseling. Check the CFM figure, the shank size and what is in the box before you order.

Check price on Amazon

Alfred Chase
Alfred Chase

Alfred Chase is the main voice behind Garage Welding, with 15 years of experience in welding. Since 2025 he has written the site's welding guides and product reviews, covering MIG, flux-core, TIG and stick welding, filler metals, welding machines, torch parts, helmets, gloves and shop safety gear. He writes for people welding in a home garage or small shop, so he sticks to what helps: clear settings, safe habits, honest limits and fixes for the problems beginners run into. His product reviews are based on manufacturer specs and listing details, and he says plainly when something isn't confirmed.

Leave a Comment

Your email address will not be published. Required fields are marked *