The Coopay welding practice kit is a set of 24 mild steel coupons, each about 2 x 4 inches, with six pieces each of 9, 11, 14 and 16 gauge. It suits beginners who want flat, consistent plate for practising beads, tacks and joints before touching a real project. It does not include a welder, wire, rod, gas or safety gear. Details here are per the listing and were not hands-on tested. The Coopay 24 pack welding practice kit gives beginners plenty of coupons to practice on.
Coopay Welding Practice Kit at a Glance
| Item | Detail |
|---|---|
| Product | Coopay 24 Pack welding practice kit |
| Material | Mild steel, low carbon (per the listing) |
| Quantity | 24 coupons, six of each thickness |
| Size | 2 x 4 inches each (per the listing) |
| Thicknesses | 9 gauge (about 0.15 in), 11 gauge (about 0.12 in), 14 gauge (about 0.07 in), 16 gauge (about 0.06 in) |
| Processes named on the listing | MIG, TIG and Stick |
| Not included | Welder, filler, shielding gas, helmet, gloves |
What Is in the Coopay Welding Practice Kit?
You get 24 pre-cut steel rectangles, so you do not have to buy a sheet and cut your own practice pieces. The four thicknesses let you see how heat input changes from thin sheet to heavier plate.
| Thickness | Typical practice use |
|---|---|
| 9 gauge (about 0.15 in) | Thickest pieces. Good for learning penetration and puddle control on heavier steel. |
| 11 gauge (about 0.12 in) | Common for brackets and frames. A good all-round practice thickness. |
| 14 gauge (about 0.07 in) | Thin enough that travel speed and heat start to matter. |
| 16 gauge (about 0.06 in) | Thinnest pieces. They show burn-through quickly, so they teach heat control. |
Who Should Buy It
A good fit if you
- are new to welding and want cheap, flat plate to practise on
- want to compare settings on different thicknesses without cutting stock
- need small pieces for testing a machine setup before a real job
Skip it if you
- want a complete starter kit with a welder or consumables
- need aluminum or stainless pieces (see the aluminum set linked below)
- want one thickness only, in larger quantity
How to Use the Coupons
- Grind or wire-brush the mill scale and any oil off the area you will weld.
- Set up your welder for the thickness using the settings chart for your machine and wire or electrode.
- Run a straight bead on a flat coupon first. Look at width, height and spatter.
- Move on to joints: butt joints, lap joints and T-joints by tacking two coupons together.
- Check the back side for penetration. Move to a thinner coupon once beads look consistent.
- Let the steel cool before handling, and store unused pieces dry so they do not rust.
Follow your welder manual for amperage, voltage and wire speed. This page does not list settings because they depend on your machine, process and consumables.
Safety
Wear a welding helmet with the correct shade, flame-resistant clothing and gloves, and weld in a ventilated area away from flammable material. Coupons stay hot for some time after welding, so use pliers or tongs.
Pros and Limitations
Pros
- Pre-cut and consistent in size
- Four thicknesses in one pack
- Low-cost way to practise without wasting project material
Limitations
- Only six pieces of each thickness
- Mild steel only, so it does not help with aluminum or stainless practice
- No consumables or equipment included
- Size and material details are per the listing and not independently measured
Related guides: Coopay aluminum welding coupons review | 24-piece steel welding practice coupons review | What is a weld coupon
Frequently Asked Questions
What is included in the Coopay welding practice kit?
Per the listing, 24 mild steel coupons about 2 x 4 inches, with six each of 9, 11, 14 and 16 gauge. No welder or consumables are included.
Can I use these for MIG, TIG and Stick welding?
The listing names all three. Your machine, filler and gas still need to suit mild steel, and you should follow the settings in your welder manual.
Can the coupons be reused?
Often yes. You can grind a bead flat and weld the other side, as long as the piece has not warped or thinned too much. The thinner 16 gauge pieces wear out fastest.
How should I store them?
Keep them dry and lightly oiled or in a sealed box, because bare mild steel rusts. Wire-brush or grind the surface clean before welding.
Is this kit good for beginners?
Yes, for practice material. It does not teach technique by itself, so pair it with a basic welding course or tutorial.