This 10 pack of weld on bullet hinges is a bulk set of small stainless steel hinges you weld to metal, mainly for gates, trailer ramps and doors, smoker lids and similar light projects. Per the listing they are 304 stainless steel, about 3-1/8 x 5/8 inches, and swing a full 360 degrees. This page covers what the set includes, where it fits, how to weld the hinges on, and what to check before you buy, since the listing gives no load rating.
Quick Specs (Per the Listing)
| Spec | Detail |
|---|---|
| Quantity | 10 hinges |
| Material | 304 stainless steel |
| Size | About 3-1/8 x 5/8 inches |
| Pin size | Listed as 5/16 x 3/4 inch |
| Rotation | 360 degrees |
| Finish | Brushed |
| Mounting | Weld on |
| Load rating | Not stated. Check the listing or ask the seller. |
What Are Weld On Bullet Hinges?
A bullet hinge has two cylindrical knuckles that look like bullet casings, with a pin joining them. You weld one knuckle to the frame and the other to the door, gate or lid. Because the knuckles are round and there are no flat leaves, the hinge looks clean and sits close to the work.
Weld on bullet hinges suit projects where you want a hidden or low-profile pivot: small gates, trailer ramps and tailgates, BBQ smoker doors and similar fabrication jobs. A 360 degree swing, as listed, means the door can open past a flat position, but it does not mean the hinge is built for heavy loads.
Who This Set Is For
- Fabricators who need several small hinges for repeat builds or a few projects.
- Hobbyists building smoker doors, tool box lids, small gates and ramps.
- Anyone who wants stainless hardware that resists surface rust better than plain steel.
Skip it if you hang heavy gates, vehicle doors or anything where a failure could injure someone. For those, use a hinge with a published load rating and weld size, or a larger weld-on hinge such as the ones in our extra heavy duty weld on hinges review.
How to Weld Bullet Hinges On
- Mark and fit. Set the frame and door in their final positions with the gap you want, and mark the hinge locations. Keep both knuckles on the same axis or the door will bind.
- Clean the metal. Remove paint, rust and mill scale where the hinge will sit, and wipe off oil.
- Tack the hinge. Tack each knuckle in place with the pin installed so the hinge stays aligned. Check the swing before you weld further.
- Weld in short runs. Use short stitches and let the part cool between them. Heat can warp a small hinge, and too much heat near the pin area can make the hinge stiff.
- Protect the pin. Keep spatter off the pin and the knuckle bore. Anti-spatter spray or a wrapped pin helps.
- Test and finish. Swing the door through its full travel, then clean and, if needed, grease the pin.
For stainless hinges welded to mild steel, a stainless filler designed for dissimilar metals is the usual choice, but check your filler manufacturer’s chart for your base metal and process.
Strengths and Limitations
Strengths
- Ten hinges in one pack, so you can hang several doors or keep spares.
- 304 stainless steel (per the listing) for better corrosion resistance than plain steel.
- Compact, low-profile design with a full 360 degree swing.
Limitations
- No load rating or weld size is given, so do not assume it fits a heavy gate.
- Small knuckles leave less weld area than a large weld-on hinge.
- Brand, tolerances and pin fit are not confirmed, so check a hinge before welding the whole pack.
How It Compares With Other Weld On Hinges
Bullet hinges are the smallest and neatest option. Larger weld-on barrel hinges and J-bolt gate hinges carry more weight and give a bigger weld surface. If you are hanging a farm or driveway gate, compare the heavy duty weldable hinges or J-bolt hinges before choosing this set.
Before You Buy
- Measure the gap you need and confirm the 3-1/8 inch length and pin size on the listing.
- Estimate the weight of the door or lid and use more or larger hinges if in doubt.
- Confirm the seller’s return terms on the listing page.
Frequently Asked Questions
Can I use these hinges on a wooden gate?
They are made to be welded, so they need a steel frame or plate to attach to. On a wooden gate you would weld the hinges to steel brackets or a steel frame and then bolt that to the wood.
How much weight can these bullet hinges hold?
The listing does not state a load rating. Treat them as light-duty hinges, use several when in doubt, and choose a hinge with a published rating for heavy gates or doors.
Are 304 stainless steel hinges rust proof?
No. 304 stainless resists corrosion much better than plain steel, but it can still stain or rust in salt or harsh conditions. Clean and dry the hinge after exposure.
What welding process works best?
TIG and MIG are both commonly used on stainless. Use short stitches, keep heat low and choose filler suited to stainless and your base metal.
How do I keep the pin from sticking after welding?
Tack with the pin installed so the knuckles stay aligned, keep spatter off the pin, weld in short runs, and add a little grease once the hinge has cooled.
Bottom Line
These 304 stainless weld on bullet hinges make sense for light doors, lids, ramps and small gates where you want a neat pivot and a bulk pack. They are not a substitute for a load-rated hinge on a heavy gate. Confirm size and fit on the listing, and test one hinge before you weld the rest.