As an Amazon Associate, Garage Welding may earn from qualifying purchases. This does not change the price you pay.
This oxy-acetylene brass quick connect is a pair of brass fittings for 9/16 inch-18 B-size torch hose connections, intended to let you detach hoses or torch handles quickly. It is worth considering if you swap attachments often on a Victor-style or similar B-size torch. Skip it if your torch uses different threads or if you prefer fixed connections with fewer joints.
Oxy-Acetylene Brass Quick Connect at a Glance
| Item | Per the listing |
|---|---|
| Type | Brass quick-connect fittings |
| Thread | 9/16 in-18 (B fitting) |
| Service | Fuel gas and oxygen |
| Listed max working pressure | Fuel 28 PSI, oxygen 142 PSI |
| Verify | Thread hand, gas marking and what is in the pack |
Check Current Price on Amazon →
What It Is and Who It Suits
A quick connect lets you break a hose connection without a wrench, usually by pulling back a sleeve. On a cutting rig it can make swapping torch handles, cutting attachments or hose sections faster.
It suits shops that change between a cutting torch, a welding torch and a heating tip, or technicians who like portable rigs. It is less useful if you set up a rig once and leave it. Every extra joint is another place to check for leaks.
How to Check It Fits Your Setup
- Thread size: The listing says 9/16 in-18 B. Many torch handles and hose nuts use this, but regulator outlets are often 5/8 in-18 (A).
- Thread hand: Oxygen is right-hand, fuel gas is left-hand with a groove. Make sure you get one for each side.
- Pressure: Compare the listing’s pressure ratings with your regulator settings. Keep acetylene at or below 15 PSI.
- Material and seals: Brass is standard; check for intact seals and smooth connection action.
- Pack contents: Look at how many sets come in the listing and whether both gases are included.
Pros and Limitations
Pros
- Faster hose and attachment changes without a wrench.
- Brass construction suited to gas service.
- Fits common B-size connections.
Limitations
- Adds a joint that must stay leak-free.
- Not a replacement for flashback arrestors or check valves.
- Quality varies with unbranded parts, so check them regularly.
Using Quick Connects Safely
- Keep oxygen fittings clean and free of oil and grease.
- Leak test every connection with soapy water after fitting, and again if the rig is moved.
- Inspect seals and springs often; replace any fitting that sticks, leaks or looks worn.
- Use flashback arrestors and check valves at the regulator or torch as your setup requires.
- Do not use on hoses that are old, cracked or burned.
- Never force a connection that does not seat; the parts may be the wrong gas or thread.
View Quick Connect on Amazon →
Quick Connect vs Threaded Fittings
Threaded nuts are the traditional choice. They are simple, widely available and have fewer parts to wear out. A quick connect trades that simplicity for speed. If you change attachments several times a day, the time saved can be worth it. If you rarely disconnect, a threaded connection with a good seat is hard to beat.
Whichever you choose, treat connections as wear items. A fitting that has been dropped, overheated or exposed to slag should be inspected or replaced, not trusted because it still clicks together.
Alternatives and Related Guides
- For replacing hose ends, see the Weldmark hose repair kit review.
- A full twin hose is covered in the X-50 twin welding hose review.
- For a complete starter rig, read the oxygen acetylene cutting torch kit review.
- For argon lines, see the Riverweld argon quick connect review.
Frequently Asked Questions
What does 9/16-18 B fitting mean?
It describes the thread on the torch or hose nut: 9/16 inch diameter with 18 threads per inch, commonly called a B-size fitting on gas welding gear. Oxygen nuts are right-hand thread and fuel gas nuts are left-hand and notched. Check your hose and torch threads before ordering.
Is a quick connect safe on an oxy-acetylene hose?
It can be convenient, but it adds a joint that can leak or wear, so choose gas-specific, well-made parts and inspect them often. A quick connect is not a flashback arrestor or check valve, and you should still use those where your setup requires them.
What do the 28 PSI and 142 PSI figures mean?
They are the maximum working pressures the listing quotes for fuel and oxygen. Acetylene working pressure must never exceed 15 PSI regardless of fitting rating, and most torches run far below the oxygen figure. Treat the ratings as upper limits, not operating targets.
Can I use the same quick connect for oxygen and fuel?
No. Keep oxygen and fuel hardware separate. Use clearly identified oxygen and fuel quick connects, with their different thread hands, and never swap them. Mixing them risks cross-connection, leaks and fire, and keep oxygen fittings free of oil and grease.
Verdict
These brass quick connects can speed up hose changes on B-size oxy-fuel rigs, provided you match thread and gas and keep up inspection. Check the current listing for pack contents before ordering.
Check Current Price on Amazon →
