The Weldmark hose repair kit is a boxed set of brass and alloy-steel hose fittings with a KT-28 hand crimper, aimed at 3/16 inch and 1/4 inch inside-diameter hose used on welding and gas equipment. It is a good fit if you keep oxy-fuel hose in service and want to replace a damaged end or splice a short section. Skip it if you need a quick fix for a badly worn hose, since replacing the hose is often the safer choice.
Weldmark Hose Repair Kit at a Glance
| Item | Per the listing |
|---|---|
| Hose sizes | 3/16 in and 1/4 in ID |
| Fittings | Brass and alloy steel, A-size and B-size |
| Tool | KT-28 hand crimping tool |
| Extras | Fitting identification chart, organizer case |
| Weight and size | About 3.1 lb, 11 x 7 x 2 in |
| Verify | Thread type and gas service of each fitting |
Check Current Price on Amazon →
What the Kit Includes and Who It Suits
A hose repair kit like this lets you rebuild a hose end that has cracked at the fitting, been burned or lost its nut. The crimper squeezes a ferrule or collar onto a barbed stem so that the hose stays attached under pressure. The case keeps the small parts organized, and the fitting chart helps with selection.
It suits owners of gas-welding rigs, repair shops and anyone who maintains a few oxy-fuel hoses. For occasional users, buying a new pre-made hose may cost about the same as the kit. The kit is more valuable if you have several hoses to maintain or hoses in unusual lengths.
How to Check It Fits Your Hoses
- Measure the ID. The kit is described for 3/16 in and 1/4 in hose. Twin welding hose is usually in these sizes, but confirm yours.
- Match the thread. A-size and B-size refer to common nut sizes. Compare to your regulator and torch connections.
- Match the gas. Oxygen uses right-hand threads and fuel gas uses left-hand threads with a groove. Use the correct nut on the correct hose.
- Check hose type. Rubber welding hose, grade and rated pressure should suit oxy-fuel. Do not mix with air hose or hose of unknown rating.
- Check the crimper. Confirm the KT-28 crimper closes fully on your ferrules, and practice on scrap hose first.
Pros and Limitations
Pros
- Fittings, crimper and chart in one organized case.
- Useful for custom lengths and replacing damaged ends.
- Brass fittings are standard for gas service.
Limitations
- Hand crimping needs a firm, even technique to get a leak-free joint.
- 3.1 lb is heavier to carry than a single fitting set.
- Not a fix for hose that is hard, cracked, burned along its length or contaminated with oil.
Using It Safely
- Close cylinder valves, bleed the lines and disconnect the hose.
- Cut the hose square with a sharp cutter, clean and inspect the cut face.
- Choose the right stem and nut, slide on the ferrule, and push the hose fully onto the barb.
- Crimp evenly following the kit instructions, then pull-test the joint by hand.
- Reconnect, pressurize slowly and leak test with soapy water.
Keep oil and grease off oxygen fittings. Pair repaired hoses with check valves and flashback arrestors at the regulator or torch, and replace hose that is old, cracked or burned.
Alternatives and Related Guides
- To replace a hose entirely, read the X-50 twin welding hose review.
- For torch-end connections, see the oxy-acetylene brass quick connect review.
- The oxygen acetylene cutting torch kit review shows what a complete setup includes.
- If the regulator end is the problem, check the Uniweld RO100 oxygen regulator review.
Frequently Asked Questions
What hose sizes does the Weldmark hose repair kit cover?
The listing describes it for 3/16 inch and 1/4 inch inside-diameter hoses, with A-size and B-size fittings and a KT-28 hand crimper. Measure your hose ID and the fitting thread before ordering, because twin welding hose and air hose are not interchangeable.
Can I use it to repair an oxy-acetylene hose?
It is sold for welding hose repair, but a leaking or burned hose is a safety item. Cut out only the damaged section if the rest is sound, use the correct fittings for oxygen or fuel gas, and leak test. When in doubt, replace the whole hose.
What do A-size and B-size fittings mean?
They refer to common hose-nut thread sizes on welding gear. In common usage B is the smaller 9/16 in-18 size and A is the 5/8 in-18 size, but confirm against the kit chart. Oxygen nuts are right-hand thread and fuel gas nuts are left-hand with a notch. Check your regulator and torch connections and the kit chart before choosing.
How do I test a hose after crimping a fitting?
Pressurize the line at working pressure with the torch valves closed, then spray soapy water on every crimp, nut and joint. Any bubbles mean a leak. Do not use the hose if a fitting spins, pulls off or weeps, and never test with a flame.
Verdict
This kit makes sense if you maintain several oxy-fuel hoses and confirm the thread and gas service of every fitting. Review the current listing before ordering.
Check Current Price on Amazon →