🔧 Practical welding guides, tested in a real garage
Gas Torch & Regulator Reviews

CAMPFIRE Argon CO2 Regulator Review: CGA 580 Fit Guide

CAMPFIRE argon CO2 regulator - product photo

The CAMPFIRE argon CO2 regulator is a brass CGA 580 regulator for MIG and TIG shielding gas, with a 0-4000 PSI inlet range and a 9.8-foot hose, according to the Amazon listing. It fits argon and argon/CO2 mix cylinders with a CGA 580 valve. Straight CO2 cylinders normally use a different outlet, so check your cylinder before you buy. This page is a listing-based buyer guide, not a hands-on test.

Check price on Amazon

CAMPFIRE Argon CO2 Regulator at a Glance

Specification Per the listing
Use MIG and TIG shielding gas
Inlet connection CGA 580
Inlet pressure range 0-4000 PSI, per the listing
Flow range 0-30 CFH for argon and 0-20 CFH for CO2, per the listing
Body Brass, per the listing
Safety Built-in pressure relief valve, per the listing
Hose 9.8 feet with hose clamps, per the listing
Not confirmed Warranty terms, gauge face size and exact outlet fittings: check the listing

Will It Fit Your Cylinder?

CGA 580 is the standard valve outlet for argon and for argon/CO2 welding mixes such as the 75/25 blend used for MIG. Straight CO2 cylinders usually use a CGA 320 outlet, which is a different thread, so a CGA 580 regulator will not screw onto them without an adapter approved for the job.

  1. Read your cylinder valve. Look for CGA 580 on the valve or ask your gas supplier.
  2. Match the gas. Confirm the regulator is intended for the gas you use.
  3. Check the flow range. The listing gives 0-30 CFH for argon and 0-20 CFH for CO2. Compare that with the flow your machine and wire chart call for.
  4. Check the machine fitting. Make sure the hose end suits your wire feeder or TIG torch gas inlet.

How to Install It Safely

  1. Crack the cylinder valve briefly to blow out dust, standing to the side of the outlet.
  2. Thread the CGA 580 nut onto the valve and tighten with a wrench. Do not use tape or sealant on the fitting.
  3. Back the adjusting screw out before opening the valve, then open the cylinder valve slowly.
  4. Connect the hose to the machine with the supplied clamps.
  5. Set the flow while gas is running, then leak-test every joint with approved solution.

Flow settings depend on your process, nozzle size and drafts in the shop. Follow your welding machine manual or wire maker chart rather than a single number.

Check price on Amazon

Pros and Limitations

Pros

  • Brass body and a built-in pressure relief valve, per the listing.
  • Includes a 9.8-foot hose with clamps, so it is ready to connect.
  • Covers argon and argon/CO2 mix cylinders with a CGA 580 valve.
  • Flow range suits typical MIG and TIG work.

Limitations

  • CGA 580 does not fit most straight CO2 cylinders.
  • Warranty and return terms were not confirmed.
  • Gauge details and outlet options need checking on the listing.
  • Not hands-on tested for flow accuracy or long-term leak performance.

To understand how a gas regulator works, how to size one for MIG, or to compare other CGA 580 regulators, see these guides.

Related guides: How a welding gas regulator works | How to size a shielding gas regulator for MIG | CGA580 argon CO2 regulators review

Frequently Asked Questions

What cylinders does the CAMPFIRE argon CO2 regulator fit?

It uses a CGA 580 inlet, which matches argon and argon/CO2 mix cylinders. Straight CO2 cylinders normally use a CGA 320 outlet, so check your valve before ordering.

What flow range does it cover?

The listing gives 0-30 CFH for argon and 0-20 CFH for CO2. Set the flow according to your welding machine manual and process.

Can it be used for both MIG and TIG?

The listing describes it for MIG and TIG shielding gas. Confirm the hose end fits your wire feeder or torch inlet.

Does it include a hose?

The listing mentions a 9.8-foot gas hose with clamps. Check what is in the box on the listing before you buy.

How often should I replace the gas hose?

There is no single interval. Inspect the hose and fittings regularly and replace the hose if you see cracks, hardening or leaks.

Conclusion

The CAMPFIRE argon CO2 regulator looks like a straightforward CGA 580 regulator for MIG and TIG if your cylinder has the matching valve. Confirm the cylinder connection, flow range and warranty terms on the listing before you order.

Check price on Amazon

Alfred Chase
Alfred Chase

Alfred Chase is the main voice behind Garage Welding, with 15 years of experience in welding. Since 2025 he has written the site's welding guides and product reviews, covering MIG, flux-core, TIG and stick welding, filler metals, welding machines, torch parts, helmets, gloves and shop safety gear. He writes for people welding in a home garage or small shop, so he sticks to what helps: clear settings, safe habits, honest limits and fixes for the problems beginners run into. His product reviews are based on manufacturer specs and listing details, and he says plainly when something isn't confirmed.

Leave a Comment

Your email address will not be published. Required fields are marked *