This 2-in-1 heavy duty bench vise has 4.5-inch jaws, a listed maximum opening of 3.3 inches and a 270 degree swivel base, so it suits small-to-medium parts in woodworking, model making and light welding prep. It is a compact vise, not a heavy blacksmith or fabrication vise, so check the jaw capacity against the work you do.
As an Amazon Associate I earn from qualifying purchases. Buying through these links costs you nothing extra.
2-in-1 Heavy Duty Bench Vise: Listed Specs
These figures come from the product listing and were not measured or bench-tested here. Confirm them on the Amazon page before ordering.
| Item | Per the listing |
|---|---|
| Jaw width | 4.5 in |
| Maximum opening | 3.3 in |
| Swivel | 270 degrees |
| Body | High-strength forged steel with a rust-protective surface coating |
| Weight | About 13 lb |
| Mounting | Screw down to a bench, or clamp on with the base (the “2-in-1” design) |
| Suggested uses | Woodworking, model making, crafts, welding prep |
Who It Suits
- Good fit: hobby woodworkers, model makers, and home garage users who need to hold small and medium parts for cutting, filing, or holding a piece while you tack it.
- Look elsewhere: if you hammer on stock, bend heavy bar, or hold large pipe. A 3.3 in opening and a light 13 lb body are not built for that. A bigger bolted vise suits that work better.
Mounting: Screw-Down or Clamp-On
The listing describes two ways to mount it. You can screw the base to a table or workbench for the most stable setup, or clamp the base to the bench edge when you want to move it. Whichever you choose, mount it on a thick, flat bench edge. A thin or hollow tabletop flexes, and the vise will shift under load.
- Pick a solid bench position where the jaws sit slightly past the bench edge.
- Fit the vise with the supplied screws, or tighten the clamp base evenly.
- Set the swivel angle, then lock it before you tighten the jaws.
- Check that the vise does not rock before you put a workpiece in.
Using It for Welding Prep
A bench vise helps hold small parts for filing, grinding and fit-up. Do not use it as a heat sink for welding or hit hot parts in it. Keep spatter and grinder sparks off the screw and jaws, and wipe the screw with light oil afterward. Wear eye protection and gloves for grinding and cutting.
Pros and Limits
- Pros: swivel base, two mounting options, forged steel body per the listing, small enough for a tight bench.
- Limits: 3.3 in opening, 4.5 in jaws, and about 13 lb of mass restrict it to light and medium jobs. Jaw material and anvil features are not stated here, so check the listing.
For a bigger or different design, see our reviews of the 4.5-inch heavy duty bench vise and the ZGJDYSM 6-inch clamp-on vise.
Related guides: ZGJDYSM 6-Inch Bench Vise Review: Specs, Fit and Uses | Heavy Duty Bench Vise 4.5 Inch Review | VEVOR Pipe Welding Vise Review
Frequently Asked Questions
What size is this bench vise?
Per the listing, it has 4.5-inch jaws and a maximum opening of 3.3 inches, and it weighs about 13 pounds.
Can I use it for metalworking?
Yes for light work such as holding small metal parts for filing, cutting or fit-up. It is not meant for heavy hammering or bending large stock.
How do I mount it?
Screw it to the bench through the base, or clamp it to the bench edge, as the listing describes. A thick, flat bench gives the most stable result.
Does the swivel base lock?
The listing gives a 270 degree swivel. Check the product page and manual for how it locks, and tighten it before clamping a part.
Is it a good vise for a small garage?
Its compact size and swivel base help in a small space. Confirm that your bench is thick and flat enough for the base before you buy.
