🔧 Practical welding guides, tested in a real garage
Gas Torch & Regulator Reviews

2 Pack Brass Inert Arc Coupler Review

Brass inert arc coupler 2 pack - product photo

The 2 Pack Brass Inert Arc Coupler is a pair of brass hose couplers for inert shielding gas lines. Per the listing, each has a 5/8-inch, 18-thread CGA-032 connection and a 200 PSI maximum working pressure, so it suits argon or helium lines whose fittings use the same thread. It will not connect to a gas cylinder valve and it is not for oxygen or fuel gas.

Quick verdict

Best for: TIG or MIG users who need to join or repair inert gas hose runs that already use 5/8-inch CGA-032 fittings.

Main limit: It only helps if your hose ends match the listed thread. Check the fittings you have before you order.

Check price on Amazon

What the 2 Pack Brass Inert Arc Coupler is

An inert arc coupler is a short brass fitting with female threads on both ends. It joins two gas hose ends, or a hose end to a torch or regulator outlet that has a matching male thread. The CGA-032 connection is the 5/8-inch, 18-thread right-hand fitting that Western Enterprises and welding supply stores list for inert arc hose couplers. The listing says this set is compatible with the Western Enterprises AW-430 coupler, which that maker describes as a brass, 200 psig inert arc hose coupler.

You get two couplers, so one can stay on the cart as a spare.

Specs at a glance

Item Detail (per the listing)
Quantity 2 couplers
Material Brass
Thread CGA-032, 5/8 inch, 18 TPI
Max working pressure 200 PSI
Gas Inert gases such as argon and helium
Listed compatibility Western Enterprises AW-430
Brand, warranty, return terms Check the Amazon listing

Is it right for your setup? Fit checklist

  • Look at the nut or fitting on each hose end. A 5/8-18 right-hand thread is what you need.
  • Confirm both ends you want to join are the type this coupler needs (it has two female ends, so it joins male fittings).
  • Confirm the gas is argon, helium or an argon blend. Do not use it on oxygen or fuel gas lines.
  • Check that your regulator, hose and torch are all rated for your working pressure. A TIG or MIG gas line normally runs at a low delivery pressure, well under the 200 PSI limit.
  • If you need an exact OEM part, compare the part number with your torch or hose maker.

If your hose ends use a different thread, such as a CGA-580 cylinder connection, this coupler will not fit.

How to install it safely

  1. Close the cylinder valve and release the pressure in the line.
  2. Inspect the brass threads on the coupler and the hose ends for dirt, burrs or damage.
  3. Start each thread by hand so it does not cross-thread, then snug it with a wrench. Do not overtighten brass.
  4. Open the cylinder valve slowly.
  5. Brush soapy water on the joints and watch for bubbles. Fix any leak before you weld.

Safety: Gas fittings are safety parts. Do not use damaged threads, and ask your gas supplier if you are unsure which fitting your equipment needs.

Pros and limitations

Pros Limitations
Brass body with a clear, standard thread to match Only fits 5/8-18 CGA-032 hose ends
Two pieces, so you have a spare Not for oxygen, acetylene or other fuel gases
200 PSI listed working pressure is far above normal shielding gas delivery Brand and warranty details are not clear from the listing

If you need a full hose repair rather than a single joint, compare the Hromee welding hose coupler adapter set or the welding hose coupler adapter set review. If the hose itself is worn, see the argon gas hose review.

Frequently Asked Questions

Will this coupler fit a gas cylinder or regulator?

Not directly. It has the 5/8-inch, 18-thread CGA-032 inert arc hose connection, which is used on hose ends and torch fittings. Cylinder valves use other connections, such as CGA-580 for argon. Check the thread on your own fitting.

Can I use it with argon or helium?

The listing describes it for inert gases such as argon and helium. Make sure the rest of your gas line is rated for the same gas and pressure.

Is the 200 PSI rating enough for welding?

The listing gives a 200 PSI maximum working pressure. TIG and MIG gas lines normally run at far lower delivery pressure, but your regulator, hose and torch must all be rated for the job.

Can I use it for oxygen, acetylene or propane?

No. It is listed for inert gases only. Use fittings that are rated and labeled for the exact gas you are using.

Do I need tools to install it?

Start the threads by hand, then snug them with a wrench without overtightening. Always check the joint with soapy water for leaks afterward.

What are the warranty and return terms?

They are not stated in the listing text I could review. Check the Amazon listing and the seller return terms before ordering.

The bottom line

This is a simple brass fitting for inert gas hose lines. Buy it only if your hose ends use the listed 5/8-inch CGA-032 thread and you are working with argon or helium. Otherwise pick a coupler that matches your fittings.

Check price on Amazon

Alfred Chase
Alfred Chase

Alfred Chase is the main voice behind Garage Welding, with 15 years of experience in welding. Since 2025 he has written the site's welding guides and product reviews, covering MIG, flux-core, TIG and stick welding, filler metals, welding machines, torch parts, helmets, gloves and shop safety gear. He writes for people welding in a home garage or small shop, so he sticks to what helps: clear settings, safe habits, honest limits and fixes for the problems beginners run into. His product reviews are based on manufacturer specs and listing details, and he says plainly when something isn't confirmed.

Leave a Comment

Your email address will not be published. Required fields are marked *