As an Amazon Associate, Garage Welding may earn from qualifying purchases. This does not change the price you pay.
The Riverweld 10N24S stubby collets are a 10-pack of copper-alloy collets sized for 3/32 inch (2.4 mm) tungsten, listed for PTA, DB, SR and WP-17, 18 and 26 style torches. They are worth considering if you run a stubby setup and want cheap spares; skip them if your torch uses standard-length collets or you weld with a different tungsten diameter.
This review is based on the Amazon listing and general TIG practice, not hands-on testing. The key question is whether a stubby collet matches your collet body, so that is covered first.
Riverweld 10N24S stubby collets at a glance
| Item | Detail |
|---|---|
| Part number | 10N24S |
| Type | Stubby TIG collet |
| Tungsten size | 3/32 inch (2.4 mm) |
| Pack (per listing) | 10 collets |
| Material (per listing) | Copper alloy |
| Listed torch fit | PTA, DB, SR, WP-17, WP-18, WP-26 style |
| Cooling | Listing mentions use on air-cooled and water-cooled torches |
Verify current details on the listing.
Check the current price on Amazon →
What it is and who it suits
A collet is the split copper sleeve that grips the tungsten and passes current to it. Stubby collets are shorter than standard ones and are used with stubby collet bodies or gas lenses and shorter back caps. That helps you reach tight corners and see the joint better, with less tungsten stick-out.
- Welders using stubby gas lens setups who go through collets regularly.
- Shops that want one size, 3/32 inch, in bulk.
- Anyone replacing worn collets that no longer grip the tungsten.
A collet only matches one tungsten diameter, so this pack is not for 1/16 or 1/8 inch electrodes.
How to check they fit your torch
- Part family. 10N24S is a stubby 3/32 inch collet number. Standard collets use different numbers and lengths. Confirm that your torch uses stubby parts.
- Torch series. Check that your torch is WP-17, 18 or 26, or a PTA, DB or SR style. Look at the collet body to be sure the thread and seating match.
- Tungsten size. Use 3/32 inch (2.4 mm) tungsten only. A mismatched collet will not grip properly.
- Back cap. A stubby setup normally pairs with a short back cap. Make sure your tungsten length suits it.
- Cooling. The listing mentions air-cooled and water-cooled use, but amperage limits come from the torch.
Pros and limitations
Pros
- A 10-pack covers many collet changes.
- Copper alloy gives good electrical contact when the collet is clean.
- Stubby length helps in tight spots.
Limitations
- One size only, so you need other packs for other tungsten diameters.
- Fit depends on matching stubby collet bodies.
- Collets wear over time and need replacing when they lose grip or discolor.
- Warranty details are not clear from the listing.
Check the current price on Amazon →
Use and care tips
- Remove the tungsten and wipe the collet bore before each change if you see dirt or burn marks.
- Do not over-tighten the back cap; it can deform or crack a collet.
- Replace a collet if the tungsten slips, if the slits close up, or if it is burned or oxidized.
- Keep spare collets in a labeled bag by size.
- Always let the torch cool before changing parts.
Alternatives and related guides
- Shimeyao 53-piece TIG consumables kit: a mixed kit with collets and cups for WP-17, 18 and 26
- #10 ceramic TIG welding cup review: a cup to pair with your collet body
- Blue tungsten electrode 3/32 review: tungsten in the same 3/32 inch size
- Pre-ground TIG tungsten electrodes: electrodes that are ready to load into a collet
Frequently Asked Questions
What size tungsten do 10N24S collets hold?
They are for 3/32 inch (2.4 mm) tungsten. A collet only grips the diameter it is made for, so use other part numbers for 1/16 inch or 1/8 inch electrodes. A loose fit causes poor current contact and an unstable arc.
What is the difference between standard and stubby collets?
Stubby collets are shorter and used with stubby collet bodies and short back caps, giving better access to tight joints. Standard collets are longer and fit standard bodies. They are not interchangeable, so match them to your collet body.
Will they fit my TIG torch?
The listing says PTA, DB, SR and WP-17, 18 and 26 style torches. Check that your torch uses stubby parts and compare part numbers with your current collet body and back cap before ordering.
When should I replace a collet?
Replace it when the tungsten slips, when the collet is burned or discolored, or when the slits have closed. A worn collet causes poor current transfer and an erratic arc, so it is a cheap part to swap.
Bottom line
The Riverweld 10N24S stubby collets are a low-cost pack of 3/32 inch spares for stubby WP-17, 18 and 26 style setups. Confirm your collet body style and tungsten size before ordering.
Check the current price on Amazon →
