🔧 Practical welding guides, tested in a real garage
MIG & TIG Torch Parts Reviews

Mtsooning 41V35 TIG Back Cap Review: 5-Pack Fit Guide

tig back cap review

The Mtsooning 5-piece 41V35 TIG back cap set is a pack of medium-length back caps for WP-9, WP-20 and WP-25 style TIG torches. It is a low-cost way to stock spares if your torch uses that cap, and a poor purchase if it does not, because back caps are not universal. Confirm the part number first. The Mtsooning 41V35 TIG back cap is a short cap for 9 and 20 series torches.

This page is based on the seller’s Amazon listing and general TIG practice, not hands-on testing.

Mtsooning 41V35 back caps at a glance

Item Per the listing
Quantity 5 pieces
Part number / size 41V35, medium length
Torch styles WP-9, WP-20 and WP-25 style torches
Brands named Rilon, Riland, Jasic and similar
Materials Plastic and copper, as listed
Weight About 1.65 oz for the pack, as listed

Check Current Price on Amazon →

What the 41V35 back cap does

The back cap closes the rear of the torch head. When you tighten it, it presses the collet so the tungsten stays in place, and it keeps shielding gas from leaking out the back. A medium cap gives a moderate length of tungsten room, between a stubby short cap and a full-length long cap.

For air-cooled WP-9, WP-20 and WP-25 style torches, the cap is a wear part. It is exposed to heat and handling, so spares are practical.

Compatibility checklist

  1. Check your torch model. WP-9, WP-20 and WP-25 are common style names, but clone torches differ.
  2. Match the part number. The listing calls out 41V35. Find your cap in the torch parts diagram.
  3. Check the thread. Try one cap by hand. It should thread smoothly with no wobble.
  4. Check length. A medium cap should hold your usual tungsten with the collet seated and some room to regrind.
  5. Check the O-ring. A good seal matters more than the cap alone. Replace worn O-rings.

Pros and limitations

Pros

  • Five spares for a small price compared with a branded replacement.
  • Fits several common torch styles, per the listing.
  • Easy to swap in minutes.

Limitations

  • Materials are plastic and copper, so treat them as light-duty parts and do not overtighten.
  • Medium length only, so you will need other caps for stubby or long setups.
  • A “fits many torches” listing still needs verification against yours.

Installing and caring for TIG back caps

Switch off the machine and let the torch cool. Unscrew the old cap, check the collet and collet body, then screw on the new cap by hand until it is snug. Do not use pliers.

Inspect caps for cracks, chips or stripped threads whenever you change tungsten. Keep spares in a dry box, away from grinding dust, so threads stay clean.

View Latest Price on Amazon →

Frequently Asked Questions

Which torches use the 41V35 medium back cap?

The listing names WP-9, WP-20 and WP-25 style TIG torches, and mentions brands such as Rilon, Riland and Jasic. Torch clones vary, so compare the 41V35 part number and thread against your torch’s parts list before ordering.

What size is the 41V35 back cap?

It is sold as a medium back cap. Medium suits a standard-length tungsten with standard collets, while a short cap pairs with stubby collet bodies and a long cap with full-length tungsten. Check the listing for the current dimensions and confirm against your torch.

How tight should a TIG back cap be?

Hand-tight is enough. The cap needs to seal the head and press the collet so the tungsten does not slip, but over-tightening with pliers can crack plastic and strip threads. If gas leaks from the back, check the O-ring and replace worn parts.

Why would I need five back caps?

Back caps are consumable. They can crack from heat, drops or over-tightening, and the plastic can wear at the threads. A five-pack keeps spares on hand for a torch you use often, and can serve several torches in a shared shop.

Conclusion

These medium 41V35 caps are a sensible spares pack if your torch uses that exact part. Verify the number and thread, then buy.

Check Price on Amazon →

Alfred Chase
Alfred Chase

Alfred Chase is the main voice behind Garage Welding, with 15 years of experience in welding. Since 2025 he has written the site's welding guides and product reviews, covering MIG, flux-core, TIG and stick welding, filler metals, welding machines, torch parts, helmets, gloves and shop safety gear. He writes for people welding in a home garage or small shop, so he sticks to what helps: clear settings, safe habits, honest limits and fixes for the problems beginners run into. His product reviews are based on manufacturer specs and listing details, and he says plainly when something isn't confirmed.

Leave a Comment

Your email address will not be published. Required fields are marked *