🔧 Practical welding guides, tested in a real garage
Clamp, Magnet & Welding Table Reviews

6-Piece Flange Wedge Set Review: 15.2 cm Stainless

6 pcs flange wedge set - stainless steel product photo

The 6 pcs flange wedge set is six stainless steel wedges, each listed at 15.2 x 3.2 cm (about 6 x 1.25 in), for leveling machinery, spacing flanges and setup work. It suits maintenance and fabrication jobs where you need small, controlled gap changes. It has no published load rating, so use it as a setup aid, never as lifting or permanent support. This review is based on the Amazon listing, not on our own bench testing.

Quick specs at a glance

Item Detail
Product Flange wedge and machinery leveling wedge set
Count 6 wedges
Listed size 15.2 x 3.2 cm (about 6 x 1.25 in) each
Material Stainless steel, per the listing
Load rating None listed
Listed uses Leveling equipment, spacing flanges, setting up machinery

Check the current price on Amazon →

What the 6 pcs flange wedge set is good for

  • Machinery leveling: small height changes before final anchoring or shimming
  • Flange spacing: opening a controlled gap for alignment or inspection where the procedure allows it
  • Shop setup: temporary support while you position a part

Stainless resists rust better than plain carbon steel in damp shops and outdoor jobs, but it still needs wiping and drying after use.

Limits and safety

  • No load rating is listed, so it is not lifting or support equipment
  • Never put hands, fingers or feet under equipment that rests only on a wedge
  • Use stands, blocks and lockout procedures for anything heavy or powered
  • Steel against finished or precision surfaces can mark them, so use a pad or follow the equipment maker’s guidance
  • Stainless wedges are not certified non-sparking. In explosive-risk areas use tools rated for that environment

How to use the wedges

  1. Clean the contact area of dirt, oil, burrs and scale so the wedge cannot slip
  2. Place the wedge on a stable point and advance it slowly, not at a hard angle
  3. Use several wedges for balanced support and reset if one side rises faster
  4. Finish with the proper shim, anchor, gasket or mount, because a wedge is a setup aid
  5. Wipe and dry the wedges before storing them

Pros and limitations

Pros

  • Six pieces cover several contact points
  • Narrow profile for controlled placement
  • Stainless construction for corrosion resistance
  • Simple and needs no power

Limitations

  • No verified load rating or hardness
  • Too small for large gaps or heavy separation
  • Not a replacement for rated lifting gear or permanent shims

Frequently Asked Questions

How many wedges are in the set?

Six wedges, each listed at 15.2 x 3.2 cm. Confirm the size on the product page before ordering.

Are they suitable for outdoor use?

Stainless steel resists corrosion well enough for damp or outdoor conditions. Clean and dry them after use.

Can they replace permanent shims or machine mounts?

No. Use wedges to position and level, then fit the correct shim, anchor, mount or fastener.

Do they have a load rating?

None is listed, so do not use them as lifting or rated support equipment.

Can I use them on any machine?

Match the wedge size and contact surface to the equipment and its procedure first. Precision or soft surfaces may need protection.

Final verdict

The 6 pcs flange wedge set is a handy, low-cost set for shop leveling and spacing when load is not critical. Skip it if you need a rated, certified or non-sparking wedge. Confirm the size and material on the current listing before you buy.

Check the current price on Amazon →

Davis Anders
Davis C. Anders

Davis C. Anders has 15 years of experience in metal cutting, grinding and fabrication, and covers that side of Garage Welding, from angle grinders and plasma cutters to abrasive discs, clamps, magnets and welding tables. He has written for the site since September 2025, with grinder safety and troubleshooting guides, plasma cutter setup and consumable advice, and DIY jig and shop-tool builds. His aim is simple: help you pick the right tool or consumable for the job, set it up properly and cut or grind metal safely. His reviews are based on manufacturer specs and listing details.

Leave a Comment

Your email address will not be published. Required fields are marked *