🔧 Practical welding guides, tested in a real garage
Clamp, Magnet & Welding Table Reviews

2 PCS Flange Wedge Review: Leveling and Spacing Use

2 pcs flange wedge - product photo

The 2 PCS flange wedge set is two steel wedges, each about 10 x 5 cm (3.9 x 2 inches) per the listing. They are made for small jobs where you need to nudge, space or level something: opening a gap between flange or mating faces, packing under a machine foot, or holding alignment while you tack.

Nothing on the listing gives a rated load, so treat them as alignment and spacing tools. Do not use them to support suspended loads or as a jack, and always match the wedge to your actual weight and contact surface.

Quick take

Best for: Pipefitters, fabricators and maintenance techs who need small steel wedges for flange spacing, leveling and fit-up.

Skip it if: You need load-rated support, certified lifting gear or a full assortment of shims.

Check first: Material and thickness on the listing, and whether a load rating is given. None is verified here.

Check price on Amazon →

Flange Wedge Specs (Per the Listing)

Spec Detail
Product 2 PCS flange wedge set
Count 2 wedges
Size About 10 x 5 cm (3.9 x 2 inches) each
Material Steel, per the listing
Finish Described as corrosion resistant; confirm coating type
Shape Beveled wedge for gradual adjustment
Load rating Not stated; do not assume one

What the 2 PCS Flange Wedge Set Is Used For

  • Flange spreading: opening a small gap between flange faces to fit a gasket or align bolt holes.
  • Machine leveling: packing under a base to remove rock or correct small height differences.
  • Fit-up: holding parts at the right angle or gap while you tack.
  • Maintenance: separating mating surfaces for inspection or cleaning.

A wedge turns a small push into a larger spreading force, which is why a pair of steel wedges is a common item in a pipefitting kit.

How to Use Flange Wedges Safely

  1. Inspect the wedges for cracks, burrs or mushroomed edges before use.
  2. Clean the contact surfaces so the wedges do not slip on oil or scale.
  3. Place them opposite each other where possible, so you spread the load evenly.
  4. Drive or press them in gradually; do not hammer hard against precision faces.
  5. Keep fingers clear of the gap. A loaded wedge can shoot out if a surface slips.
  6. Take the load off and remove them before you start final welds or torque bolts.

Wear gloves and eye protection, and block the work with proper supports if there is any chance of movement.

Check price on Amazon →

Pros and Limitations

Pros Limitations
Compact size fits a tool bag No load rating on the listing
Steel construction per the listing Small size limits how large a gap you can open
Simple, reusable design Steel on steel can mark soft or machined faces
Two in a set for even spreading Not a replacement for a shim set or a jack

Alternatives

Larger flange spreaders and alignment tools handle bigger gaps, shim packs give finer height control, and pipe spacer wedges suit pipe fit-up. The related reviews below cover other flange wedge sets so you can compare sizes and counts.

Related reading: 4 PCS flange wedge review · 12 pcs flange wedge set · Bueyfolt flange wedge · pipe spacer wedge

Frequently Asked Questions

What size are these flange wedges?

The listing gives about 10 x 5 cm, or roughly 3.9 x 2 inches, per wedge. Check the thickness at the thick end if your gap is large.

How much weight can they hold?

No rated load is stated on the listing. Use them for alignment and spacing, and use rated supports for heavy loads.

Can I leave them in place while welding?

Remove them before final welding. Wedges under load can shift, and weld heat and spatter can mark them.

Are they good for leveling machinery?

They can work for small corrections under a machine foot, but use rated leveling feet or shims for permanent installation.

What is the difference between a flange wedge and a pipe spacer wedge?

A flange wedge spreads or aligns flange faces and mating surfaces. A pipe spacer wedge sets a gap between pipe ends for fit-up and root-gap control.

Bottom Line

The 2 PCS flange wedge set is a simple, compact pair for spreading, spacing and small leveling jobs. Keep it in the alignment-tool category, not the load-support category, and confirm material and current price on the listing.

Check price on Amazon →

Davis Anders
Davis C. Anders

Davis C. Anders has 15 years of experience in metal cutting, grinding and fabrication, and covers that side of Garage Welding, from angle grinders and plasma cutters to abrasive discs, clamps, magnets and welding tables. He has written for the site since September 2025, with grinder safety and troubleshooting guides, plasma cutter setup and consumable advice, and DIY jig and shop-tool builds. His aim is simple: help you pick the right tool or consumable for the job, set it up properly and cut or grind metal safely. His reviews are based on manufacturer specs and listing details.

Leave a Comment

Your email address will not be published. Required fields are marked *