Disclosure: As an Amazon Associate, we earn from qualifying purchases. If you click a link on this page and make a purchase, we may receive a small commission at no extra cost to you.
Holding metal pieces steady can slow you down when you need clean corners, repeatable angles, or a safer tack-welding setup. The Spurtar Welding Magnets aim to solve that problem with a 6-piece set that supports 45°, 90°, and 135° positioning. Each magnet is described as holding up to 75 lbs on compatible ferrous metal, which gives you useful support for common fabrication and assembly jobs. This review explains where these magnets help most, where they have limits, and what you should check before buying.
Quick Verdict
Rating: 8.4/10
Best For: DIY welders, small-shop fabricators, and metalworkers who need repeatable angle holding on ferrous metal.
Bottom Line: Spurtar Welding Magnets are worth considering if you want hands-free support for common 45°, 90°, and 135° setups. They are less useful if you work with aluminum, stainless grades with weak magnetic response, painted surfaces, or parts that exceed the stated holding capacity.
Key Specifications
| Specification | Detail |
|---|---|
| Brand | Spurtar |
| Product type | Welding magnets and magnetic angle holders |
| Count | 6 pieces |
| Holding capacity | Up to 75 lbs per magnet, based on the article-supported claim |
| Supported angles | 45°, 90°, and 135° |
| Color | Bright red for easier visibility |
| Compatibility | Ferrous metal objects only |
| Design notes | Arc-shaped bottom for tubing alignment and center hole for added handling or positioning support |
| Best use | Welding setup, fabrication, marking, assembly, and magnetic separation of small ferrous parts |
Key Takeaways
- The Spurtar Welding Magnets are designed to hold ferrous metal pieces while you align, tack weld, mark, or assemble parts.
- The set includes six magnetic holders, which helps when you need support at more than one corner or workpiece.
- Each magnet supports 45°, 90°, and 135° angles, so it covers common square, miter, and angled fabrication layouts.
- The bright red finish improves visibility on busy workbenches and helps you spot the magnets before striking an arc.
- The stated 75 lb capacity is useful, but real holding strength depends on surface contact, metal thickness, cleanliness, and workpiece shape.
What Is the Spurtar Welding Magnets Set?
The Spurtar Welding Magnets set is a group of magnetic angle holders for metalworking. You use them to hold compatible ferrous metal pieces in place while you measure, mark, tack weld, or assemble a project.
The main appeal is simple: you get six holders that can support three common angles. The magnets help free your hands, reduce small alignment errors, and speed up setup when clamps are awkward or when you need temporary positioning before a final weld.
Before You Buy: These magnets work on ferrous metal only. They are not the right tool for aluminum, copper, brass, plastic, wood, or non-magnetic stainless surfaces.
Who Should Buy It?
Best For
- DIY welders who need quick 90° corner support for frames, brackets, or repair work.
- Metalworkers who want repeatable 45°, 90°, and 135° setups without holding parts by hand.
- Small shops that can use several magnets at once for layout, marking, and light assembly tasks.
Skip If
- You mainly work with aluminum or other non-ferrous materials.
- You need precision fixturing for heavy production welding or exact machining tolerances.
- Your workpieces are dirty, painted, curved, oily, or too heavy for the stated capacity.
Design and Build Quality
The bright red body is more than a cosmetic detail. It helps you see the magnets on a crowded bench, inside a fabrication area, or near darker steel parts. Better visibility can also reduce the chance of leaving a magnet attached to a workpiece before grinding, heating, or moving it.
The article-supported design includes an arc-shaped bottom, which helps when you need to align tubing or round stock. That shape gives you a more practical contact point than a flat-only holder when the workpiece is not a simple rectangular bar.
The center hole adds another useful detail. It can make the magnet easier to grab, reposition, hang, or stabilize during setup. It does not turn the magnet into a lifting device, but it helps with handling during normal shop use.
Holding Strength and Metal Contact
Each Spurtar magnet is described as supporting up to 75 lbs. That number gives the set enough holding force for many common metalworking tasks, especially when you are aligning steel before tack welding.
You should still treat the rating as a best-case support figure, not a guarantee in every setup. Magnetic hold changes when the steel is thin, rough, rusty, painted, dirty, curved, oily, or hot. Full face contact on clean ferrous metal gives you the best chance of stable holding.
Pro Tip: Clean the contact area before positioning the magnet. Mill scale, grinding dust, oil, paint, and weld spatter can reduce grip and cause small alignment shifts.
Angle Support and Alignment
The three supported angles, 45°, 90°, and 135°, cover many of the layouts you are likely to use in a small welding or fabrication setup. A 90° angle helps with square corners, while 45° and 135° positions help with mitered parts, angled braces, and layout work.
This angle support is useful when you need a quick reference point before tack welding. The magnets can hold parts close to position while you check measurements and make small adjustments. They should not replace careful measuring, squaring, or clamping when the finished part needs tight tolerances.
Hands-Free Operation
Hands-free support is the biggest reason to buy welding magnets. Instead of holding two pieces of steel with one hand and trying to tack weld with the other, you can position the parts and keep both hands free for safer tool control.
This can improve workflow during small fabrication jobs. You can set a corner, check the angle, tack it, and move to the next section with less frustration. With six pieces in the set, you can also support more than one joint at a time.
Versatile Applications Beyond Welding
While the Spurtar Welding Magnets are mainly designed for welding setup, they can also help with layout, marking, assembly, and temporary holding. If you work with ferrous metal shelves, brackets, frames, tubing, or small parts, the magnets can keep pieces organized and easier to position.
They can also help with magnetic separation during bench work. You can use them to keep small ferrous pieces from rolling away or to gather metal items during a project. Keep in mind that they are shop aids, not certified lifting tools or permanent fixtures.
How It Performs in Real Use
For Square Corner Setup
The 90° position is the most useful angle for many buyers. It helps when you build frames, brackets, shelf supports, gates, or small repair pieces. You still need to verify squareness with a square or measuring tool before final welding.
For Tubing and Round Stock
The arc-shaped bottom makes the magnets more practical around tubing than a flat-only holder. You can use the magnet to help steady round or curved ferrous pieces while you mark or prepare a tack. For larger pipe or heavy tube, add clamps or proper supports.
For Marking and Layout
The magnets can act as temporary positioning helpers when you mark cut lines, compare angles, or hold a workpiece against another part. This is useful when you want a third hand but do not need a full fixture table setup.
For Small-Shop and DIY Use
A 6-piece set gives you enough holders for multiple corners or repeatable setups. That makes the set useful for home garages, mobile repair kits, hobby fabrication, and small shop benches where space is limited.
How to Use Spurtar Welding Magnets Correctly
- Use them only on ferrous metal: Test the magnet on the material before planning your setup.
- Clean the contact surface: Remove dust, oil, loose rust, paint, and spatter where the magnet will sit.
- Check the angle before welding: Use a square, angle finder, or measuring tool before final tack welds.
- Do not overload the magnet: The stated capacity depends on ideal contact and does not replace clamps for heavy parts.
- Keep heat in mind: Avoid placing magnets where direct heat, sparks, or molten metal can damage the tool or shift the setup.
- Store them clean and dry: Wipe off metal dust after use so the magnetic faces stay easier to position next time.
Compatibility and Safety
Spurtar Welding Magnets are compatible with ferrous metals. That usually means magnetic steels and iron-based materials. They will not hold non-magnetic materials, and they may perform poorly on coated, painted, very thin, or irregular surfaces.
Use normal welding safety practices when you work around them. Wear proper eye protection, gloves, and welding gear. Keep fingers clear when the magnet snaps onto metal, and keep magnets away from electronics, magnetic storage devices, watches, and medical devices unless the device manufacturer says it is safe.
Do not use these magnets as lifting equipment. They are positioning tools for setup and alignment. If a workpiece could fall, shift, or injure someone, support it with clamps, stands, fixtures, or another load-rated method.
Pros and Cons
Pros
- Supports 45°, 90°, and 135° angles for common welding and layout tasks.
- 6-piece set gives you more flexibility than a single magnetic holder.
- Stated 75 lb holding capacity is useful for many small and medium ferrous metal setups.
- Bright red color makes the magnets easier to spot in a busy work area.
- Arc-shaped bottom helps when aligning tubing or round ferrous stock.
Cons
- Not suitable for aluminum, copper, brass, wood, plastic, or non-magnetic stainless steel.
- Holding strength can drop on painted, dirty, curved, oily, or thin metal surfaces.
- Not a replacement for clamps, stands, or precision welding fixtures on heavy or high-tolerance work.
Is It Worth the Price?
The Spurtar Welding Magnets set offers strong practical value if you often need a quick way to hold ferrous metal at common angles. You get six holders instead of one, which makes the set more useful for frames, repeated corners, and multi-point alignment.
It is worth considering if you want a simple shop accessory that can speed up setup without adding a complicated fixture system. The main limitation is compatibility. If your work involves non-ferrous metals or precision production jigs, these magnets will not replace specialized clamps or fixture tables.
How It Compares to Alternatives
Compared with smaller magnetic angle holders, the Spurtar set makes sense when you want more holding force and several magnets in one package. Compared with switchable on/off welding magnets, this set is simpler, but it may take more care to remove from metal and keep clean.
If you need fine adjustability, a dedicated welding clamp or fixture table may be better. If you want quick positioning for common angles on ferrous metal, the Spurtar Welding Magnets are a practical middle ground.
Frequently Asked Questions
What materials work with Spurtar Welding Magnets?
They work with ferrous metal objects, such as magnetic steel or iron-based materials. They will not hold aluminum, copper, brass, plastic, wood, or non-magnetic stainless surfaces.
Can these magnets hold a full 75 lbs in every setup?
No. The stated 75 lb capacity depends on good surface contact and compatible ferrous metal. Dirt, paint, oil, curved parts, thin steel, and uneven contact can reduce the hold.
What angles do the Spurtar Welding Magnets support?
They support 45°, 90°, and 135° angles. That makes them useful for square corners, angled braces, mitered layouts, and general metal assembly.
Can I use them for tubing?
Yes, the article-supported design includes an arc-shaped bottom for tubing alignment. For heavy pipe, large round stock, or safety-critical work, add clamps or proper supports.
How do I clean and maintain welding magnets?
Wipe off metal dust, grinding debris, oil, and spatter after use. Store the magnets dry and avoid abrasive cleaning that could damage the working surfaces.
Can these welding magnets be used outdoors?
You can use them for outdoor metalworking tasks when the material is compatible, but do not assume they are weatherproof. Dry them after use and store them indoors to reduce wear.
Are these a replacement for welding clamps?
No. They are helpful positioning aids, not load-rated clamps or fixtures. Use proper clamps, stands, and supports when the workpiece is heavy, unstable, or safety-critical.
What warranty does the Spurtar Welding Magnets set include?
A specific warranty period could not be verified from the article-supported details. Check the current Amazon listing, seller terms, or product packaging before you rely on warranty coverage.
The Bottom Line
The Spurtar Welding Magnets set is a smart buy if you want six magnetic holders for common ferrous metal alignment tasks. Its strengths are the 45°, 90°, and 135° angle support, bright red visibility, and stated 75 lb holding capacity, while its main limitation is that real grip depends on material and surface contact.
Buy it for DIY welding, layout, marking, and small-shop fabrication. Skip it if you need a certified lifting magnet, a precision fixture system, or a solution for non-ferrous materials.
