Disclosure: As an Amazon Associate, we earn from qualifying purchases. If you click a link on this page and make a purchase, we may receive a small commission at no extra cost to you.
Holding two steel pieces steady while you tack, mark, or square a joint can slow down even a simple welding job. The Spurtar Welding Magnets Set is made to give you extra hands by holding ferrous metal at common shop angles. This review helps you decide if its six-piece mix of 25 lb, 50 lb, and 75 lb magnets is enough for your work. The main strength is simple angle support for fit-up and layout, while the main limitation is that these magnets only grip magnetic metal and should not replace clamps for heavy, hot, or overhead work.
Quick Verdict
Rating: 8.4/10
Best For: DIY welders, small-shop users, and fabricators who need fast 45°, 90°, and 135° setup support.
Bottom Line: The Spurtar Welding Magnets Set is a practical helper for holding ferrous metal during layout, tack welding, soldering, and marking. It is best for temporary positioning, not for supporting heavy parts without clamps or safe backup support.
| Specification | Detail |
|---|---|
| Brand | Spurtar |
| Product type | Welding magnet set |
| Amazon ASIN from link | B07JVD9RYX |
| Count | Six welding magnets |
| Holding capacities | 25 lb, 50 lb, and 75 lb rated magnets across the set |
| Supported angles | 45°, 90°, and 135° positioning |
| Compatible materials | Ferrous metal such as magnetic steel and iron |
| Not compatible with | Aluminum, copper, brass, and many non-magnetic stainless steels |
| Build detail | High gloss enamel end plates noted in the source article |
| Best use | Welding fit-up, assembly, soldering support, layout, and marking |
| Care note | Wipe off filings, dust, and moisture before storage |
Key Takeaways
- The Spurtar Welding Magnets Set includes six magnets with 25 lb, 50 lb, and 75 lb holding capacities for different shop tasks.
- The magnets support 45°, 90°, and 135° positioning, which helps with square corners, angled joints, and repeat layout work.
- They are made for ferrous metal only, so they will not hold aluminum, brass, copper, or many stainless parts.
- The compact shape makes the set easy to move around a bench, frame, bracket, or small fabrication project.
- They are useful for hands-free setup, but you should still clamp or support heavy, hot, or overhead workpieces.
What Is the Spurtar Welding Magnets Set?
The Spurtar Welding Magnets Set is a six-piece group of magnetic welding holders. The set includes magnets rated at 25 lb, 50 lb, and 75 lb, so you can choose a smaller holder for light layout work or a stronger holder for heavier fit-up.
The main job of these magnets is to hold ferrous metal at set angles before or during a task. You can use them at 45°, 90°, and 135° angles, which covers many common welding, soldering, marking, and assembly layouts.
They are most useful when you need quick temporary positioning. They do not replace a proper clamp, fixture, jack stand, or safe work support when the part is heavy, unstable, hot, or overhead.
Before You Buy: These magnets only grip ferrous metal. Do not buy them for aluminum, copper, brass, or non-magnetic stainless projects unless you also have another way to clamp and hold the work.
Who Should Buy It?
Best For
- DIY welders who need a simple way to hold steel at common angles.
- Small-shop users who want several magnet strengths in one set.
- Fabricators who do frequent layout, marking, tack welding, or bracket assembly.
Skip If
- You mostly work with aluminum, brass, copper, or non-magnetic stainless steel.
- You need a precision fixture for production welding with tight repeatability.
- You expect magnets to hold heavy overhead parts without clamps or supports.
Key Features and Benefits
Six Magnets for Different Holding Needs
The set includes six magnets across 25 lb, 50 lb, and 75 lb capacities. That range gives you more flexibility than a single magnet because not every job needs the largest holder. A smaller magnet can be easier to place in tight areas, while a stronger magnet can help with heavier steel pieces during setup.
The listed holding capacities are best treated as ideal holding ratings. Real holding strength can change based on surface condition, metal thickness, paint, rust, dirt, heat, angle, and how much leverage the part puts on the magnet.
45°, 90°, and 135° Angle Support
The biggest practical benefit is angle positioning. A 90° hold helps with square tube, frames, brackets, and corner joints. A 45° or 135° hold can help when you are setting braces, angled tabs, small gussets, or layout marks.
This saves time because you can position the part, check the angle, and tack more easily. It also helps keep your hands farther from pinch points and hot work areas, but it does not remove the need for gloves, eye protection, and safe welding habits.
Compact Shape and Shop-Friendly Handling
The compact design makes the magnets easy to move around a bench or workpiece. You can place one inside a corner, use another on the outside edge, or combine magnets when you need extra temporary control.
The source article notes high gloss enamel end plates, which help the set feel more finished and durable. Even so, you should avoid dropping the magnets, dragging them across finished surfaces, or letting metal filings build up on the faces.
Pro Tip: Clean both the magnet face and the steel before setup. Paint, scale, rust, grinding dust, and weld spatter can reduce grip and make your angle less accurate.
How It Performs in Real Use
For Tack Welding and Fit-Up
For light and medium steel fit-up, the Spurtar magnets can help hold parts in position while you place tack welds. This is useful when you are building small frames, brackets, shelves, stands, carts, or shop fixtures.
For best results, use the magnet to position the pieces first, then check the angle with a square or measuring tool before welding. Heat, weld pull, and uneven gaps can still move the joint, so the magnet should support your setup rather than replace careful fitting.
For Assembly and Layout Work
The magnets are also useful before welding starts. You can use them to hold steel pieces while you mark cut lines, test a bracket position, or check the general shape of a small project.
This can make the workflow faster because you are not trying to hold a piece with one hand and mark with the other. It is especially helpful when working alone on a bench or floor-level project.
For Soldering, Marking, and Light Shop Tasks
The article notes use for soldering and marking. For these tasks, the magnets can act as simple holders when the material is magnetic and the part is not too heavy.
Keep heat in mind. Magnets should not be placed where direct flame, arc heat, or heavy spatter can damage the magnet or reduce its grip. Move the magnet away from the hottest part of the work whenever the setup allows it.
For Outdoor or Jobsite Use
The set can be useful outdoors because magnetic holders do not need power and are easy to carry. They can help with quick layout and temporary steel positioning in a driveway, garage, farm shop, or mobile repair setup.
Outdoor use also adds dirt, moisture, and surface rust. Wipe the magnets dry after the job and remove metal debris from the faces before storage.
How to Use It Correctly
Start by checking that the workpiece is ferrous and clean. Place the magnet on a flat section of metal, then set the second piece against the angle face. Once the parts are positioned, check the angle with a square, protractor, or measuring tool before welding.
Use tack welds first. After tack welding, let the joint settle, then confirm the angle again before running a longer bead. For heavier parts, add clamps, supports, or blocks so the magnet is not carrying the full load.
- Use the 25 lb magnets for lighter layout, small pieces, and easier handling.
- Use the 50 lb and 75 lb magnets when you need stronger temporary holding on heavier steel.
- Avoid dragging the magnet across painted or finished surfaces because trapped filings can scratch.
- Keep the magnet away from direct weld puddles, heavy spatter, and high heat when possible.
- Store the magnets dry and away from loose metal shavings.
Compatibility and Safety Notes
The Spurtar Welding Magnets Set is designed for ferrous metal. That means it works with magnetic steel and iron, but it will not grip aluminum, copper, brass, or many stainless steel alloys. Before you plan a project around these holders, test the material with the magnet first.
Because magnets can snap onto steel quickly, keep your fingers clear when placing them. Wear welding gloves and eye protection, and do not use the magnets as lifting tools. They are positioning aids, not rated lifting devices.
Be careful near electronics, pacemakers, watches, magnetic cards, and sensitive tools. Strong magnets can affect nearby magnetic or electronic items, so keep them away from anything that could be damaged.
Pros and Cons
Pros
- Six-piece set gives you more setup options than a single welding magnet.
- 25 lb, 50 lb, and 75 lb capacities cover light and medium shop tasks.
- 45°, 90°, and 135° angles support common welding and layout positions.
- Useful for hands-free fit-up, marking, soldering support, and assembly work.
- Compact shape makes the magnets easy to place and store.
Cons
- Only works on ferrous metal, not aluminum, brass, copper, or many stainless parts.
- Not a replacement for clamps, fixtures, or support stands on heavy workpieces.
- Grip can drop on rusty, painted, dirty, thin, hot, or uneven metal surfaces.
Is It Worth the Price?
The Spurtar Welding Magnets Set makes the most sense as a budget-friendly shop helper for everyday steel layout and small welding projects. You get six magnets in one set, which is useful if you often need more than one holder at the same time.
It is worth considering if you want simple angle support without building a dedicated fixture for every small job. The value is strongest for DIY welders, garage fabricators, and users who work with square tube, flat bar, brackets, and mild steel pieces.
It is not the best fit if you need production-grade repeatability or if most of your work involves non-magnetic metals. In those cases, adjustable clamps, purpose-built fixtures, or a welding table setup may be a better buy.
How It Compares to Alternatives
Compared with a single welding magnet, this Spurtar set gives you more flexibility because it includes six holders and three strength levels. That can be more useful for small projects where you need several pieces held at once.
Compared with adjustable clamps or dedicated welding fixtures, these magnets are faster to place but less secure under load. Choose the Spurtar set for quick positioning and layout. Choose clamps or fixtures when the joint must stay locked in place during heavy welding, grinding, or repeated production work.
Frequently Asked Questions
What materials can the Spurtar welding magnets hold?
They are made for ferrous metal, such as magnetic steel and iron. They will not grip aluminum, copper, brass, or many non-magnetic stainless steel parts.
Are the 25 lb, 50 lb, and 75 lb ratings always exact in real use?
No. Holding strength depends on the metal thickness, surface condition, angle, cleanliness, and load direction. Rust, paint, grinding dust, thin metal, and heat can all reduce grip.
Can these magnets replace clamps?
They can help with temporary positioning, but they should not replace clamps for heavy, unstable, overhead, or high-heat work. Use clamps, blocks, stands, or fixtures when the part must stay locked in place.
Can the magnets damage painted or finished surfaces?
They can scratch a finished surface if metal filings or grit are trapped between the magnet and the workpiece. Clean the magnet face first and lift it away instead of dragging it across the surface.
Are these magnets suitable for outdoor use?
They can be useful for outdoor steel projects, especially for quick layout and temporary holding. After outdoor use, wipe off moisture, dirt, and filings before storing them.
How should you clean the welding magnets?
Use a dry cloth, damp cloth, or mild detergent when needed. Remove metal shavings from the faces and let the magnets dry fully before storage.
Who should skip this welding magnet set?
Skip it if your work is mostly aluminum or non-magnetic stainless steel. You should also skip it as your only holding method for heavy structural parts, overhead work, or precision production fixtures.
What is the warranty period for this product?
A specific warranty period was not confirmed from the supplied article. Check the Amazon listing, seller details, and package information before purchase if warranty coverage matters to you.
The Bottom Line
The Spurtar Welding Magnets Set is a useful buy if you work with ferrous metal and want quick 45°, 90°, and 135° positioning for welding, soldering support, marking, and assembly. Its six-piece mix of 25 lb, 50 lb, and 75 lb magnets gives you good flexibility for small-shop and DIY work.
Skip it if you need a clamp replacement, a production fixture, or holders for aluminum and other non-magnetic metals. The verdict matches the 8.4/10 rating: recommended for practical steel setup work, with clear limits around material compatibility and load support.
