🔧 Practical welding guides, tested in a real garage
Welding Power & Electrical Reviews

N043321 Air Compressor Rocker Switch Review and Fit Guide

N043321 rocker switch - product photo

The N043321 rocker switch is a replacement on/off switch listed for DeWalt air compressors, including the D55146, D55167 and D55168 models. Check the part number and your compressor model before you order, because several different switches look alike. Everything below comes from the product listing, not from hands-on use. The N043321 air compressor rocker switch replaces the power switch on compatible compressors.

Key Takeaways

  • It is a rocker (on/off) switch, not a pressure switch. If your compressor will not shut off at pressure, the pressure switch is the likely fault instead.
  • The listing names DeWalt D55146, D55167 and D55168 compressors (Types 6 to 9) as compatible.
  • The listing gives a 20A, 250V AC rating, IP55 dust and water protection and 4-pin terminals.
  • Match the part number printed on your old switch or in the compressor parts diagram before buying.

N043321 Rocker Switch Specs (Per the Listing)

Item Listed detail
Part number N043321
Type Rocker (on/off) switch with 4 pin terminals
Electrical rating 20A at 250V AC (voltage range listed as 125-250V)
Protection IP55 dust and water resistance; flame-retardant housing
Body size 0.845 x 1.115 inches (listed)
Fits DeWalt D55146, D55167, D55168 (Types 6, 7, 8, 9) per the listing

We could not confirm these figures against a DeWalt parts page, so treat them as the seller’s claims and compare with the switch you are removing.

Compatibility Checklist Before You Order

  1. Find the model and type number on the compressor data plate, for example D55146 Type 7.
  2. Look up that model’s parts diagram and confirm the rocker switch part number.
  3. Compare the terminal layout (4 pins) and the cutout size with your old switch.
  4. Confirm your compressor runs on a supply voltage inside the switch rating.

How to Replace a Compressor Rocker Switch

  1. Unplug the compressor and let it sit until motor and tank are cool.
  2. Open the tank drain valve and release all air pressure.
  3. Remove the switch cover or housing screws to reach the back of the switch.
  4. Photograph the wiring, then label each wire before you pull any terminal.
  5. Release the old switch from its panel cutout and disconnect the terminals.
  6. Connect the wires to the same terminals on the new switch and snap it into the cutout.
  7. Refit the cover, plug in, and test the switch with the tank empty before filling it to full pressure.

If you are not comfortable with mains wiring, have an electrician or service shop do it. A loose terminal can overheat under motor load.

Troubleshooting After the Swap

  • Motor will not start: recheck terminal connections and the overload reset on the motor.
  • Switch feels loose in the panel: the cutout size does not match. Return it rather than forcing it.
  • Compressor still will not shut off: the rocker switch is not the cause. Look at the pressure switch and check valve.
  • Switch clicks but nothing runs: test for power at the switch and check the cord and thermal overload.

Limitations to Know

  • It only fits the models the listing names, and only if the cutout and terminals match.
  • Check the listing page for the seller’s return and warranty terms before you buy.
  • It is an aftermarket-style part. If you need a genuine part, order by number from a DeWalt parts dealer.

Related reading: Metabo HPT 6-gallon pancake compressor review and our pancake air compressor roundup.

Frequently Asked Questions

Will the N043321 rocker switch fit my DeWalt compressor?

The listing names the D55146, D55167 and D55168 (Types 6 to 9). Check the type number on your data plate and compare the old switch before you order.

Is this the same as a pressure switch?

No. A rocker switch only turns power on and off. A pressure switch senses tank pressure and starts or stops the motor. A compressor that will not cut out at pressure usually needs the pressure switch checked.

What are the listed electrical ratings?

The listing gives 20A at 250V AC with 4 pin terminals. Confirm that against your compressor motor and the parts diagram.

Is it safe to replace the switch myself?

It is a basic wiring job if you unplug the unit, drain the tank, and label every wire before removing it. Use a qualified person if you are unsure about electrical work.

What does IP55 mean on this switch?

IP55 is a protection rating for dust and low-pressure water jets. It does not make the switch submersible, so keep the compressor out of standing water.

Alfred Chase
Alfred Chase

Alfred Chase is the main voice behind Garage Welding, with 15 years of experience in welding. Since 2025 he has written the site's welding guides and product reviews, covering MIG, flux-core, TIG and stick welding, filler metals, welding machines, torch parts, helmets, gloves and shop safety gear. He writes for people welding in a home garage or small shop, so he sticks to what helps: clear settings, safe habits, honest limits and fixes for the problems beginners run into. His product reviews are based on manufacturer specs and listing details, and he says plainly when something isn't confirmed.

Leave a Comment

Your email address will not be published. Required fields are marked *