The Delta Plus Go Spec II (sold by Elvex as the Go-Specs II) is a foam-lined safety glasses and goggle hybrid with an anti-fog polycarbonate lens. It is general impact eye protection for the shop, not welding eye protection: it does not replace a welding helmet or a shade-rated filter lens for arc work. This review covers what the manufacturer and retailer sheets state, who it suits, and where its limits are.
Delta Plus Go Spec II specs at a glance
| Spec | Detail (per manufacturer and retailer sheets) |
|---|---|
| Product line | Delta Plus / Elvex Go-Specs II safety glasses with foam seal |
| Lens | Polycarbonate with SuperCoat anti-fog coating |
| Frame and padding | Nylon frame with EVA foam padding |
| Retention | Length-adjustable elastic strap, or rubber-tipped temples on some variants |
| Fit adjustments | Pantoscopic (tilt) angle adjustment |
| Fog control | Ventilation channels at the top and bottom plus the anti-fog coat |
| UV protection | About 99% to 99.9% depending on the sheet; check your variant |
| Impact standard | ANSI Z87.1 (sheets cite Z87.1-2010+ and Z87.1-2015); confirm the markings on your pair |
| Other ratings | EN166 and MIL-PRF-31013 ballistic rating on the manufacturer sheet |
| Weight | Not listed on the sheets checked |
Is the Delta Plus Go Spec II safe for welding?
Not for arc welding. Clear and lightly tinted safety lenses do not filter the arc, so you still need an auto-darkening helmet or a correctly shaded filter for striking an arc. Some Go-Specs II variants are sold with tinted or IR-filter lenses, but check the shade number against your process before using one near a flame, and never use them as a substitute for a helmet.
Where they do fit a welding shop is everything else: grinding, chipping slag, wire brushing, drilling and cutting prep. For heavy grinding, wear a face shield over safety eyewear. See face shield vs safety glasses for angle grinder work for the reasoning.
Fit and comfort
The EVA foam seal fills the gap between lens and face, which helps keep dust and debris out and makes the glasses feel like a light goggle. The pantoscopic adjustment lets you tilt the lens to sit properly in front of your eyes, and the elastic strap keeps the frame in place when you look down at a workpiece.
- Try the fit with your hearing protection and respirator, because foam and strap can interfere with earmuffs and mask straps.
- Wear them for a full task before relying on them. Foam seals can feel warm in hot shops.
- Prescription wearers: the sheets checked do not say whether the glasses fit over prescription frames, so test the fit or look at dedicated over-the-glasses models.
Lenses, UV and anti-fog
The lens is polycarbonate, a common choice for impact protection. The SuperCoat anti-fog layer and the ventilation channels work together to limit fogging, which is the main complaint with sealed eyewear. The sheets describe the coating as anti-scratch and washable, but any polycarbonate lens will scratch if you wipe it dry, so clean it with water or lens cleaner and a soft cloth.
Lens colors vary by listing (clear, gray and IR-filter versions appear at retailers). Buy the lens that matches your lighting and task, and read the listing carefully before ordering.
Pros and limitations
Pros
- Foam-lined seal and strap for a snug, goggle-like fit.
- Anti-fog coating plus ventilation channels.
- Impact-rated polycarbonate lens with UV protection.
- Pantoscopic tilt adjustment.
Limitations
- Not welding eyewear and not a replacement for a helmet.
- Weight and prescription compatibility are not stated on the sheets checked.
- Foam can feel warm in long sessions.
- Variants differ, so check lens type, strap or temples and markings on the listing.
Who should buy it
Buy it if you want snug, anti-fog impact eyewear for grinding, woodworking, drilling or general garage work. Skip it if you need arc-welding protection, a wide face shield, or glasses designed to fit over a prescription frame. For shade-rated glasses, see the Miller Shade 5.0 safety glasses review and the HARFINGTON welding safety glasses review.
Frequently Asked Questions
Can I use the Delta Plus Go Spec II for arc welding?
No. They are impact safety glasses, not an arc-welding filter. Use a welding helmet with the correct shade for the process, and wear safety glasses under it.
Are they ANSI Z87.1 rated?
The manufacturer sheet cites ANSI Z87.1-2010+ and a retailer lists Z87.1-2015. Check the markings printed on your frame and lens to confirm.
Do they fit over prescription glasses?
The sheets checked do not say. Try them on with your frames, or consider an over-the-glasses model or prescription inserts.
How do I clean the lenses without scratching them?
Rinse off grit first, then use lens cleaner or mild soap and a soft cloth. Avoid dry wiping, solvents and abrasive cleaners.
What warranty do they carry?
The sources checked do not state a warranty. Check the seller listing and packaging before you buy.
Bottom line
The Delta Plus Go Spec II is a sensible foam-lined, anti-fog safety eyewear option for dusty, spark-and-chip shop work, as long as you treat it as impact protection and not as welding eyewear. Confirm the lens type and standards markings on the exact variant you order.