The Gloxyuni flat copper welding spoon is a hand-held copper backing tool, not a welder. You hold it behind a thin panel, gap or hole while you MIG weld from the front, and the copper helps keep molten steel from falling through or sticking. It suits auto body repair and thin sheet-metal patching; skip it if you want a spot welding machine.
This review is based on the Amazon listing and common copper-backing practice. The tool was not hands-on tested.
Quick specs at a glance
| Item | Details |
|---|---|
| Item | Flat copper spoon with wood handle |
| Copper plate | About 2 mm thick, per the listing |
| Handle | Natural wood insulated handle |
| Fastening | Stainless steel dual-bolt, per the listing |
| Length | About 12.99 in overall, per the listing |
| Weight | About 10.2 oz, per the listing |
| Used for | Backing thin metal during MIG welding, hole and gap filling |
Specs come from the listing and manufacturer information; confirm them on the live page.
What a copper welding spoon is and who it suits
Copper conducts heat quickly and steel weld metal does not normally stick to it, so a copper plate makes a handy backing. Body shops use a spoon behind a thin panel to fill holes, close plug-weld holes and tack panels that do not have a lot of rear access.
The Gloxyuni is a flat spoon with a wood handle. It suits hobbyists and restorers who weld thin sheet steel and want to reduce burn-through. Despite sometimes being sold as a spot welder, it does not generate current or weld by itself.
How to check it fits your work
- Panel access: you need to reach behind the work. If you cannot, a copper backing strip or ceramic backing may suit better.
- Shape: a flat spoon works on flat panels and straight seams. For curved panels, check how the plate shape matches.
- Hole size: the tool is meant to bridge small holes and gaps, so check the plate is large enough.
- Welding process: it is used mainly with MIG. Check with the seller before using it with TIG or with aluminium, because heat sinks and contamination matter.
- Handle clearance: the wooden handle can scorch, so keep it away from the arc and hot metal.
Pros and limitations
Pros
- Copper pulls heat away and helps prevent burn-through on thin steel.
- Steel spatter typically does not weld to copper, so it is easy to clean.
- Light at about 10 oz and comfortable with a wood handle.
- A simple, low-cost accessory for patching.
Limitations
- It is a backing aid, not a welding machine.
- Copper can heat up and burn your hand if you hold it near the arc for long.
- It cannot replace a clamp or fixture on parts that need alignment.
- Surfaces can become pitted by spatter and need cleaning.
How to use it and stay safe
- Clean the metal and remove paint, rust and coatings in the weld area.
- Hold the spoon firmly against the back of the gap or hole, with welding gloves on.
- Weld in short tacks or stitches so the panel does not warp.
- Allow the spoon to cool between welds, and stop if the handle begins to scorch.
- Brush off spatter with a wire brush once cool.
Wear a proper welding helmet, flame-resistant clothing and gloves. Do not weld galvanized, plated or unknown coated metal without ventilation and respiratory protection, since the fumes are hazardous.
Alternatives and related guides
Related gear includes the welding anti-spatter compound review for easier cleanup, the welding table clamps review for holding panels, and the spot weld cutter kit review for removing old factory welds.
Frequently Asked Questions
Is the Gloxyuni copper spoon a spot welder?
No. It is a copper backing tool. You hold it behind a panel while you MIG weld from the other side. It does not produce current and cannot weld on its own.
Why use copper behind a weld?
Copper conducts heat quickly and steel weld metal generally does not bond to it. This helps support the weld pool across a gap and reduces burn-through on thin sheet metal, though it is not a guarantee.
Can I use it with a TIG welder?
The listing focuses on MIG welding. TIG can work with copper backing in some setups, but heat and contamination matter, so check with the seller and keep the tungsten away from the copper surface.
How do I clean the spoon?
Let it cool, then brush off spatter with a soft wire brush. Avoid grinding aggressively because that removes copper and changes the shape. Keep it dry to limit tarnish.
Conclusion
The Gloxyuni copper welding spoon is a simple, light backing tool for thin-panel MIG work. It helps with gaps and holes, but it is not a welder and not a clamp. Check the current listing for price and details.