🔧 Practical welding guides, tested in a real garage
Welding Tools & Accessories Reviews

Therwen 9-Piece Welding Practice Kit Review: 16 Ga Coupons

welding practice kit review

The Therwen 9-piece welding practice kit is a set of nine small mild steel coupons in eight shapes, made from 16-gauge sheet, and aimed at people learning to weld. This welding practice kit review is based on the Amazon listing, not on hands-on testing.

It is worth considering if you want a cheap, ready-cut set of small pieces to practice beads, tacks and simple joints. Skip it if you want a large supply of plate for repeated joint-position practice, or you are learning with thicker steel than 16 gauge.

Quick specs at a glance

Item Details
Product type Welding practice coupons, 9 pieces in 8 styles
Material (per listing) Mild steel, 16 gauge
Thickness (typical for 16 ga steel) About 0.06 in (1.5 mm)
Size (per listing) About 1.5 in per coupon
Processes named (per listing) MIG, TIG, gas and stick

The thickness is the standard value for 16 gauge sheet steel and is not quoted from the listing. Confirm exact shapes and sizes on the product page.

What the kit is and who it suits

Practice coupons let you run beads and build joints without cutting your own pieces. Because each coupon is small, they are quick to weld and cheap to waste. Eight different shapes give you variety, such as flat plate, dice-like cubes or other geometric forms, which is useful for practicing fit-up, tacking and stacking.

They suit beginners who want to get hands-on time, hobby welders testing machine settings and teachers who need small samples.

What you can practice, and what thin steel means

16 gauge is thin enough to burn through if amperage or travel speed is wrong. That makes it a good teacher for MIG heat control, but a harder one for stick welding.

  • MIG: good for practicing tacks, short stitch beads and lap joints on thin steel. Use a small wire size such as 0.023 or 0.030 in and settings from your machine chart.
  • TIG: great for learning puddle control on thin mild steel. Use argon and clean the surface first.
  • Stick: possible with small electrodes at low amps, but burn-through is common. Treat stick practice on thin coupons as advanced.
  • Oxy-fuel: small tips and low pressure only. Follow your regulator and torch guidelines.

How to check the kit fits your practice plan

  • Joint types: small coupons are fine for beads and tacks; for butt joints or fillet joints in different positions, check how many matching pieces you receive.
  • Size: at about 1.5 in, they are small to hold. Use pliers or clamps, plus gloves.
  • Quantity: nine coupons are quickly used up. Plan to buy extra scrap or a larger practice pack.
  • Cleaning: mild steel may carry mill oil or coating. Clean to bare metal before welding.

Pros and limitations

Pros

  • Pre-cut and varied shapes for quick practice.
  • Thin mild steel teaches heat control.
  • Low cost per piece compared with buying sheet and cutting it.

Limitations

  • Small quantity.
  • Too thin for deep penetration or heavy-amp practice.
  • Small pieces heat up fast, so hold with pliers.
  • No instructions or procedures supplied beyond the shapes.

Practice tips and safety

  1. Wear a proper helmet, gloves, a flame-resistant jacket and closed-toe leather boots.
  2. Clamp coupons in a vise or hold with locking pliers; they get very hot.
  3. Tack first, then run short beads, and let pieces cool between passes.
  4. Cut a finished joint open or bend it to see the penetration.
  5. Quench hot coupons only if safe, and don’t touch a coupon you did not see cool.

Keep a fire extinguisher nearby and clear flammables from the bench.

Frequently Asked Questions

What is 16 gauge steel in inches?

Standard 16 gauge sheet steel is about 0.06 in (1.5 mm) thick. Gauge numbers vary slightly by material, but for mild steel this is the common value.

Can a beginner use these coupons for stick welding?

It is difficult. Thin 16 gauge steel burns through easily with stick electrodes. Use a small rod and low amperage, or practice stick on thicker plate first.

Do I need to clean the coupons first?

Yes. Remove oil, rust and mill scale with a wire brush or abrasive so you weld on bare metal. This improves arc stability and weld quality.

How many welds can I get from nine coupons?

That depends on how you use them. Small coupons mainly give you beads, tacks and a few joint practice builds. Plan on extra scrap if you want longer sessions.

Final verdict

This kit is a modest, convenient pack of thin steel coupons for beginners. Treat it as a starter set, expect to use extra scrap for volume and always follow PPE and fire safety rules.

Alfred Chase
Alfred Chase

Alfred Chase is the main voice behind Garage Welding, with 15 years of experience in welding. Since 2025 he has written the site's welding guides and product reviews, covering MIG, flux-core, TIG and stick welding, filler metals, welding machines, torch parts, helmets, gloves and shop safety gear. He writes for people welding in a home garage or small shop, so he sticks to what helps: clear settings, safe habits, honest limits and fixes for the problems beginners run into. His product reviews are based on manufacturer specs and listing details, and he says plainly when something isn't confirmed.

Leave a Comment

Your email address will not be published. Required fields are marked *